Journals →  Non-ferrous Мetals →  2015 →  #2 →  Back

METAL PROCESSING
ArticleName Development and research of method of obtaining of bimetallic steel-copper billet for electrometallurgical purposes
DOI 10.17580/nfm.2015.02.06
ArticleAuthor Dovzhenko N. N., Arkhipov G. V., Sidelnikov S. B., Konstantinov I. L.
ArticleAuthorData

Siberian Federal University, Krasnoyarsk, Russia:

N. N. Dovzhenko, Professor of a Chair “Plastic Metal Working”
S. B. Sidelnikov, Professor, Head of the Department “Plastic Metal Working”
I. L. Konstantinov, Assistant Professor of the a Chair “Plastic Metal Working”, e-mail: ilcon@mail.ru

 

LLC “RUSAL Engineering and Technological Centre”, Krasnoyarsk, Russia:

G. V. Arkhipov, Director of the Project “Energy efficient design of electrolyzers”

Abstract

The method is conducted and the possibility of obtaining large steel-copper bimetallic blank of rectangular section, intended for use as a cathode rod aluminum cell is studied. The results of the series of experiments to find the temperature, time and deformation parameters of connection technology copper and steel plates of different thicknesses are given. For the purpose of obtaining of steel-copper bimetal, the connected surfaces of blanks made of steel St3 (Ст3) and copper M1 were polished, degreased with acetone, collected in a pack, compressed on hydraulic press and fixed in the compressed state with the screw connection clamps. After this the packet was placed in a muffle furnace and heating modes was varied from 800 to 1050 oC at various time of exposure within the furnace. The samples were rolled on a duo-200 mills with smooth rollers or in closed box pass. Rolling is conducted without prior heating of the samples after the heating in the temperature range from 800 to 1050 oC. Holding of the compressed package for 30–60 minutes in the temperature range 900–1050 oC results in the welding of copper and steel. The resulting composite blank can be subjected without breaking machining for removing the surface layer. The following hot rolling of composites in the section mill pass in the same temperature range has allowed them to deform without fracture of the weld, and the total degree of deformation of blanks adjustment was 10–20%. Test bimetal has shown that shear strength weld samples after diffusion bonding were ~50 MPa, and after rolling increased to 70 MPa. To test the feasibility of the method developed in the laboratory testing was made on the modes of diffusion welding of large samples with sizes of cross-section close to the size of electrolytic cathode rods: steel — 115x230 mm, copper — 12x150 mm. Metallurgical studies weld natural samples and tests have shown compliance with section properties and structure of the weld data obtained in the model samples.

These investigations were carried out by employees of LLC “RUSAL Engineering and Technology Centre” in cooperation with scientists of the Siberian Federal University in the framework of the Federal Target Program “Priority research and development of scientific-technological complex of Russia for 2014–2020” on the theme “Development of aluminum obtaining technology with a reduction of energy consumption in operating electrolyzer at 300–1000 kW/t of aluminum by agreement No. 14.579.21.0032 for subsidies.

keywords Aluminum, electrolytic, bimetal steel-copper, diffusion welding, bar rolling, the cathode rod weld
References

1. Blais M., Désilets M., Lacroix M. Energy Savings in Aluminum Electrolysis Cells: Effect of the Cathode Design. Light Metals. 2013. pp. 627–631.
2. Gagnon M., Goulet P., Beeler R., Ziegler D., Fafard M. Optimization of the Cathode Collector Bar With a Copper Insert Using Finite Element Method. Light Metals. 2013. pp. 621–626.
3. Chuvichilov V. A., Kuzmin S. V., Lysak V. I., Dolgiy Yu. G., Kokorin A. V. Issledovanie struktury i svoystv kompozitsionnykh materialov, poluchennykh po batareynoy skheme svarki vzryvom (Investigation of structure and properties of composite materials, obtained by battery-operated scheme of explosion welding). Izvestiya Volgogradskogo gosudarstvennogo tekhnicheskogo universiteta = Bulletin of Volgograd State Technical University. 2010. Vol. 5, No. 4. pp. 34–43.
4. Ogolikhin V. M., Shemelin S. D. O sozdanii kompozitsionnykh materialov s zadannoy teploprovodnostyu svarkoy vzryvom (About the creation of set thermal conductivity composite materials by explosion welding). Tekhnologiya mashinostroeniya = Mechanical engineering technology. 2008. No. 4. pp. 5–8.
5. Kuzmin S. V., Lysak V. I., Rybin V. V., Peev A. P. Osobennosti plasticheskoy deformatsii metalla okoloshovnoy zony pri svarke vzryvom raznorodnykh metallov (Peculiarities of plastic deformation of weld adjacent zone metal during explosion welding of various metals). Izvestiya Volgogradskogo gosudarstvennogo tekhnicheskogo universiteta = Bulletin of Volgograd State Technical University. 2010. Vol. 5, No. 4. pp. 4–11.
6. Zakharenko I. D. Svarka metallov vzryvom (Explosion welding of metals). Minsk : Nauka i tekhnika, 1990. 205 p.
7. Kazakov N. F. Diffuzionnaya svarka materialov (Diffusion welding of materials) Moscow : Metallurgiya, 1976. 312 p.
8. Golovanenko S. A. Svarka prokatkoy bimetallov (Rolling welding of composite metals). Moscow : Metallurgiya, 1977. 160 p.
9. Ilchenko N. I., Didenko S. Yu., Neklyudov I. M., Bondarenko S. L. Poluchenie metodom goryachey prokatki v vakuume sloistykh i kompozitsionnykh materialov tipa med-stal i issledovanie ikh svoystv (Obtaining of “copper-steel” type composites by hot vacuum rolling and investigation of their properties). Voprosy atomnoy nauki i tekhniki = Problems of atomic science and technology. 2003. No. 3. pp. 158–160.
10. Zarapin Yu. L., Chichenev N. A., Chernilevskaya N. G. Proizvodstvo kompozitsionnykh materialov obrabotkoy davleniem (Pro duction of composite materials by pressure treatment). Moscow : Metal lurgiya, 1991. 351 p.
11. Bakkalolu Ö. F. A magnetic study of sputtered Fe/Cu multilayer films. Journal of Magnetism and Magnetic Materials. 1998. Vol. 182. pp. 324–328.
12. Bunshah R. F., Nimmagadda R., Doerr H. J., Movchan B. A., Grechanuk N. I., Dabizha E. V. Structure and property relationships in microlaminate Ni–Cu and Fe–Cu condensates. Thin Solid Films. 1980. Vol. 72. pp. 261–275.
13. Song J. S., Hong S. I., Park Y. G. Deformation processing and strength/conductivity properties of Cu–Fe–Ag microcomposites. Journal of Alloys and Compounds. 2005. Vol. 388. pp. 69–74.
14. Stepanov N. D., Kuznetsov A. V., Salishchev G. A., Khlebova N. E., Pantsyrny V. I. Evolution of microstructure and mechanical properties in Cu–14%Fe alloy during severe cold rolling. Materials Science and Engineering: A. 2013. Vol. 564. pp. 264–272.
15. Maa Liang-Cai, Zhang Jian-Min, Xu Ke-Wei. Magnetic and electronic properties of Fe/Cu multilayered nanowires: a first-principles investigation. Physica E. 2013. Vol. 50. pp. 1–5.
16. Grünberger W., Heilmaier M., Schultz L. Highstrength, high-nitro gen stainless steel-copper composite wires for conductors in pulsed high-field magnets. Materials Letters. 2002. Vol. 52, Iss. 3. pp. 154–158.

Language of full-text english
Full content Buy
Back