Journals →  Non-ferrous Мetals →  2016 →  #1 →  Back

METAL PROCESSING
ArticleName Modeling of butt and lap joint laser welding of aluminum alloys and constructional steel sheets
DOI 10.17580/nfm.2016.01.05
ArticleAuthor Shlegel A. N., Evtikheev N. N., Gusev D. S., Ivanchenko A. B.
ArticleAuthorData

Vladimir State University named after Alexander and Nikolay Stoletovs, Vladimir, Russia:

A. N. Shlegel, Head of Laboratory of the laser technologies research and application of the Engineering Center, Assistant Professor of Automation of technological processes Department, e-mail: shlegel81@rambler.ru

D. S. Gusev, Engineer of Laboratory of the laser technologies research and application of the Engineering Center
A. B. Ivanchenko, Assistant Professor, Mechanical Engineering Department

 

National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Moscow, Russia:

N. N. Evtikheev, Head of Laser Physics Department

Abstract

Recently the most claimed at the market are technologies of body components and parts obtaining which combine multi-metal welding. Such technologies are especially needed on the railway and motor transport as well as in special production. Manufacturing of the motor transport frame units consisting of steel skeleton and sheet aluminum coating allows to improve their corrosion resistance and essentially decrease weight of the carriers, which consequently contribute to the fuel consumption lowering. Residual deformations originated from the welding process negatively affect the welded construction qualitative characteristics, such as strength, harshness, containment, corrosion resistance, etc. Stress level reduction is available by means of the welded seam form and quality, which depend on the welding process technological parameters. Determination of rational technological parameters of the welding processes requires taking into account the used rolled metal features, namely different thermal conduction of materials, significantly bigger (≈50%) coefficient of linear (thermal) expansion inherent to non-ferrous metals as compared to carbon steel, foamed metal-oxide layer formation on the surface of the weld leading to deterioration of corrosion resistance. The article is devoted to the modeling process of the laser welding modes impact upon strength properties of the weld of aluminum alloy and constructional steel sheets. Presented are an algorithm and results of the finite-element analysis simulation modeling of the butt and lap joint laser welding by the example of AMg2M (АМг2М) aluminum alloy and St3 (Ст3) steel samples. Weld strength properties obtained experimentally and by modelling are compared. It is demonstrated that the worked out simulation model of multi-metal sheets laser welding may be used for theoretical study of the butt and lap joint welding of any other heterogeneous materials.

The work was supported by the Ministry of Education and Science of the Russian Federation. Agreement on grant No. 14.577.21.0158 of November 28, 2014. Unique identifier PNIER (ПНИЭР) RFMEFI57714X0158.

keywords Laser welding, lap joint welding, butt welding, simulation model, method of finite-element analysis, aluminum alloy, steel, residual stresses, ultimate breaking load, tensile strength
References

1. Birger A. I. Ostatochnye napryazheniya (Residual stresses). Moscow : Mashgiz, 1963. 232 p.
2. Costa J. M. et al. Residual stresses analysis of ND-YAG laser welded joints Engineering Failure Analysis. 2010. Vol. 17. pp. 28–37.
3. Dai H. Modelling Residual Stress and Phase Transformations in Steel Welds. Neutron Diffraction. 2012. pp. 49–76.
4. Alieva S. G. et al. Promyshlennye aluminievye splavy: spravochnik (Сommercial aluminum alloys : reference book). Ed. by F. I. Kvasova, I. N. Fridlyander. — 2nd ed., revised and complemented. Мoscow : Metallurgiya (Metallurgy), 1984. 527 p.
5. Marochnik stalei i splavov : spravochnoe izdanie (Reference book of alloys and steels grades). Ed. by A. S. Zubchenko. — 2nd ed., revised and complemented. Moscow : Mashynostroenie (Mechanical engineering), 2003. 784 p.
6. Shapeev V. P, Isaev V. I., Tcherepanov A. N. Tchislennoye modelirovanye lazernoi svarki stalnykh plastin (Laser welding of steel plates computational modeling). Fisicheskaya mezomekhanika = Physical mesomechanics. 2011. Vol. 14, No. 2. pp. 107–114.
7. Sudnik W., Radaj D., Breidschwerdt S., Erofeew W. Numerical Simulation of weld pool geometry in laser beam welding. J. Phys. D: Appl. Phys. 2000. Vol. 33. pp. 662–671.
8. Swapnil R. D., Sachin P. A., Awanikumar P. Finite Element Analysis of Residual Stresses on Ferritic Stainless Steel using Shield Metal Arc Welding. International Journal of Engineering Research and General Science. 2015. Vol. 3. No. 2. pp. 1131–1137.
9. Pospishil B. et al. Prochnost i dolgovechnost elementov energeticheskogo oborudovaniya (Durability and longevity of power equipment pieces). Ed by V. N. Kiselevskiy. Kiev : Naukova Dumka, 1987. 216 p.
10. Pospisil B. Zobecneni Neuberova principu smerodatne deformace k vypoctum v oblasti stridave plastike deformace. Strojirenstvi. 1975. Vol. 25. No. 2. S. 74–78.
11. Troshchenko V. T. Rasseyannoye ustalostnoye povregdeniye metallov i splavov. Soobshcheniye 3. Deformatsionnye i energeticheskiye kriterii (Diffused fatigue damage of metals and alloys. Report 3. Deformation and energetic criteria). Problemy prochnosty = Problems of Durability. 2006. No. 1. pp. 5–31.
12. Shiganov I. N., Shakhov S. V., Kholopov A. A. Lasernaya svarka aluminievykh splavov aviatsionnogo naznacheniya (Laser welding of aviation aluminum alloys). Vestnik MGTU im. N. E. Baumana. Ser. “Mashynostroenie” (Herald of the Bauman Moscow State Technical University. Series Mechanical Engineering). 2012. No. 6. pp. 34–50.

Full content Modeling of butt and lap joint laser welding of aluminum alloys and constructional steel sheets
Back