Journals →  CIS Iron and Steel Review →  2016 →  #2 →  Back

ArticleName Production of ingots with favourable location of internal defects owing to varying the features of solidification of its head part
DOI 10.17580/cisisr.2016.02.05
ArticleAuthor D. V. Rutskii, N. A. Zyuban, S. B. Gamanyuk
ArticleAuthorData

Volgograd State Technical University (Volgograd, Russia)

D. V. Rutskii, Cand. Eng., Associate Professor, Department “Technology of materials”, rutskiy79@mail.ru
N. A. Zyuban, Dr. Eng., Professor, Head of Department “Technology of materials”, tecmat49@vstu.ru
S. B. Gamanyuk, Cand. Eng., Associate Professor, Department “Technology of materials”, gamanuk@mail.ru

Abstract

Solidification of large ingots is accompanied by development of the defects of shrinkage and segregation origination in these ingots. Such defects can reach significant size, remain in forgings after ingot deformation and lead to metal rejects at fabrication stage. At present time, serious attention is paid to the problems of manufacture of defect-free ingots. Any of such investigations present information about usage of the new technologies providing substantial improvement of ingot quality parameters. These methods make the ingot production process rather more complicated and expensive, especially for the case of fabrication of long hollow forging, what restricts possibility of their wide application. This work proposes the method of ingot production for hollow forgings, allowing to control forming and development of internal axial defects due to local chilling of the ingot head part, and to guarantee their complete removal during forging. It was established during metallographic examinations as well as physical and mathematical simulation that local chilling of the ingot head part leads to acceleration of solidification process practically in the whole ingot volume. Calculation of thermal work of chilling and hot feeder heads has revealed lowering of heat transferred to the body of chilled ingot. It stipulated increase of solidification rate and decrease of chemical heterogeneity in cast metal. Displacement of a thermal center to the axial part of the middle ingot section finalized in optimal location of a shrinkage, having essential length and small diameter; such location provides its guaranteed removal during fabrication of hollow ingot forging.

The reported study was funded by RFBR, according to the research project No. 15-08-08098 А and No. 16-08-01029 А, and tender СП-2015 (СП-4573.2015.1).

keywords Ingots, solidification, chemical and physical heterogeneity, shrinkage, segregation, physical and mathematical simulation, shrinkage hole
References

1. Durynin V. A., Solntsev Yu. P. Issledovanie I sovershenstvovanie tekhnologii proizvodstva s tselyu povysheniya resursa stalnykh izdeliy is krupnykh pokovok otvetstvennogo naznachenia (Study and improvement of production technology for increase of service life of steel products of responsible usage). Saint-Petersburg : Khimizdat. 2006. 272 p.
2. Ikeda Y., Morinaka K., Muraoka T. Recent Technological Progress on Large Ingots for Rotor Forgings. 18th International Forgemasters Market and Technical Proceedings (September 12–15, 2011). Pittsburgh, PA, USA : 2011. pp. 166–169.
3. Dyudkin D. A., Kisilenko V. V. Proizvodstvo stali. Vol. 3. Vnepechnaya metallurgiya stali (Steelmaking. Vol. 3. Ladle treatment of steel). Moscow : Teplotekhnik. 2010. 544 p.
4. Smirnov A. N. Zatverdevanie metallicheskogo rasplava pri vneshnikh vozdeistviyakh (Solidification of metal melt in the conditions of external effects). Donetsk : VIK Publishers. 2008. 250 p.
5. Efimov V. A., Eldarkhanov A. S. Tekhnologii sovremennoy metallurgii (Modern metallurgical technologies) Moscow : Novye tekhnologii. 2004. 784 p.
6. Tomioka A., Nishihara M., Nishiguch K. Quality of the work roll by new ESR. 16th IFM. 2009. pp. 75–84.
7. Dub A. V., Dub V. S., Kriger Yu. N. et al. Elektroshlakovyi pereplav — sposob kardinalnogo povysheniya kachestva i svoistv otvetst vennykh izdeliy v sovremennom mashinostroenii. Tekhnicheskie trebovaniya i novye resheniya (Electric slag remelting as the method of cardinal improvement of quality and properties for responsible products in the modern machine-building. Technical requirements and new solutions). Tyazheloe mashinostroenie = Heavy machinery. 2012. No. 6. pp 2–6.
8. Jiang Z.-H., Liu F.-B., Yu Q., Chen X., Zang X.-M., Deng X. Development of a new technology for manufacture of hollow ingots by electroslag remelting process. Kang T’ieh/Iron and Steel. 2015. Vol. 50. Iss. 10. pp. 30–36.
9. Dub V. S., Romashkin A. N., Malginov A. N. et al. Razvitie tekhnologii razlivki stali v slitki (Development of the steel ingot casting technology). Tyazheloe mashinostroenie = Heavy machinery. 2012. No. 8. pp. 2–8.
10. Zhbankov I. G., Perig A. V. Forging of ingots without hot tops. Materials and Manufacturing Processes. 2013. Vol. 28. No. 3. pp. 229–235.
11. Machovák P., Tkadleková M., Opler A., Carbol Z., Trefil A., Michalek K. The development of new type of 90 ton forging ingot. Conference Proceedings: 23rd International Conference on Metallurgy and Materials, METAL 2014. Czech Republic. 2014. pp. 72–80.
12. Rutskiy D. V., Zyuban N. A. Development of defect zones and cast metal structure in elongared two-piece Cr-Ni-Mo steel ingots. CIS Iron and Steel Review. Vol. 2015. Iss. 10. pp. 14–18.
13. Sang-Hun Oh, Jung Namkung, Seog-Ou Cho, Dong-Hee Lee. A Study on the Fabrication of a Large Hollow Ingot by CAE. 18th International Forgemasters Market and Technical Proceedings (September 12-15, 2011). Pittsburgh, PA, USA : 2011. pp.179–182.
14. Ao G. W., Shen M. G., Zang Z. S., Li B. L. Study on unidirectional solidification ingot with hollow lateral wall insulation. Metalurgija. 2016. Vol. 55, Iss. 4. pp. 597–600.
15. Liu M., Ma Q. X. Modeling and numerical simulation research on hollow steel ingot forging process of heavy cylinder forging. 4th International Conference on Manufacturing Science and Engineering, ICMSE 2013; Dalian. China. 2013. Vol. 712–715, pp. 627–632.
16. Nazaratin V. V., Kobelev O. A., Efimov M. V., Selyutin A. A., Yavtushenko P. M. Analysis of technologies used to make hollow ingots and prospects for their improvement. Metallurgist. 2013. Vol. 56, Nos. 9–10.
17. Shamrey V. A., Zhulyev S. I. Novaya forma kuznechnogo slitka dlya izgotovleniya polykh kovanykh izdeliy (New shape of a forged ingot for manufacture of hollow forgings). Metallurg = Metallurgists. 2007. No. 11. pp. 54–57.
18. Zhulyev S. I. Optimizatsiya protsessov proizvodstva kuznechnykh slitkov dlya pokovor otvetstvennogo naznacheniya s ispolzovaniem SAPR-tekhnologiy (Optimization of manufacturing processes of forged ingots for forgings of responsible application using SAPR technologies). The thesis of Dr. Eng. Volgograd : 1991. 372 p.
19. Kolodkin M. V. Optimizatsiya teplovoy raboty kuznechnykh slitkov dlya proizvodstva polykh izdeliy s uluchshennymi tekhnikoekonomicheskimi pokazatelyami (Optimization of heat work in forged ingots for manufacture of hollow products with improved technical and economical parameters). The thesis of Cand. Eng. Moscow : TsNIITMASh. 2010. 140 p.
20. Zyuban N. A., Rutskii D. V., Galkin A. N., Gamanyuk S. B., Kosova E. A., Puzikov A. Ya. Model izlozhnitsy dlya issledovaniya protsessa ktistallizatsii slitkov (Mold model for investigation of the process of ingot crystallization). P. m. 135551. МPК B22D7/08. Patent RF № 2013120789/02. Applicant and patentee: FBGOU VO “VolgGTU”. Declared on 06.05.2013; published on 20.12.2013.
21. Zyuban N. A., Rutskii D. V., Galkin A. N., Gamanyuk S. B., Kosova E. A., Puzikov A. Ya. Model izlozhnitsy dlya issledovaniya protsessa ktistallizatsii slitkov (Mold model for investigation of the process of ingot crystallization). P. m. 141550. МPК B22D7/08. Patent RF № 2014100754/02. Applicant and patentee: FBGOU VO “VolgGTU”. Declared on 09.01.2014; published on 10.06.2014.
22. Bagmutov V. P., Zakharov I. N., Zyuban N. A., Rutskii D. V., Gamanyuk S. B. Sistema kompyuternogo modelirovaniya “Crystal” (System of computer-aided simulation “Crystal”). State registration certificate for the ECM program № 2013613206 dated 28.03.2013. Applicant and patentee: FBGOU VO “VolgGTU”. Declared on 12.02.2013; published on 20.06.2013.
23. Rutskii D. V. Issledovanie khimicheskoy neodnorodnosti kuz nechnykh slitkov dlya krupnogabaritnykh zagotovok tyazhelogo mashinostroeniya (Investigation of chemical heterogeneity of forged ingots for large-size billets used in heavy machinery). The thesis of Cand. Eng. Moscow : TsNIITMASh. 2006. 134 p.

Full content Production of ingots with favourable location of internal defects owing to varying the features of solidification of its head part
Back