Journals →  Tsvetnye Metally →  2018 →  #1 →  Back

METAL PROCESSING
ArticleName Criteria for choice of parameters of friction stir welding of thin aluminium sheets
DOI 10.17580/tsm.2018.01.12
ArticleAuthor Drits A. M., Ovchinnikov V. V., Bakshaev V. A.
ArticleAuthorData

Arconic SMZ, Moscow, Russia

A. M. Drits, Executive Officer of Business Development and New Technologies, e-mail: Alexander.Drits@arconic.com

 

Moscow Polytechnic University, Moscow, Russia

V. V. Ovchinnikov, Professor of a Chair “Materials Science”

 

Cheboksary Enterprise “Sespel”, Cheboksary, Russia

V. A. Bakshaev, Executive Officer

Abstract

We defined the optimum parameters of friction stir welding, widely used in welded structure manufacturing using various aluminium alloys with 3.0–8.0 mm thickness. Friction stir welding of aluminium sheets obtains high-quality seams by the right choice of the tool depth in welded metal, the tool rotation frequency and its linear displacement speed along the joint or welding speed. The length of tool’s linear displacement along the joint for its one turn may be used as a friction stir welding parameter, defining the heat input in seam formation zone. Optimal rational range is defined, showing the tool’s linear displacement length along the joint for its one turn, and providing the high-quality formation of seams of Al – Mg alloys and other aluminium alloys. Conditions of plastic deformation of metal in permanent connection formation zone are defined by its heating temperature and deformation velocity, depending on the tool rotating frequency and velocity of its linear displacement along the joint. Our experimental investigation proved the qualitative formation of seams with friction stir welding of aluminium alloys at various values of these parameters. According to our calculations, high temperature at friction stir welding is reached with the contact of aluminium alloy with tool’s rotating shoulder. Temperature of aluminium alloy 1565ch in the area of contact with tool’s rotating shoulder may reach 620–648 oC: formation of thin metal layer in solid-liquid state is possible in the zone of contact of working tool’s shoulder with surface of welded billets. Aluminium alloy 1565ch is successfully welded with rather high speeds of welding. Optimal ratio Vweld/N for the alloy 1565ch is in the range of 0.04–0.38 mm/turn. Welding speed can be changed in the range of 4–18 m/hour and 8–34 m/hour with tool rotating speeds 1200 turn/min and 2000 turn/min, respectively. Welding speed should be decreased at friction stir welding for obtaining of qualitative compounds on denser aluminium alloys, containing rather large quantity of alloying and modifying elements. Using the tool with low diameter of plastified metal volume shoulder for friction stir welding could be insufficient for complete filling of the area retrievable behind the tool, leading to incomplete fusion in seams.

keywords Friction stir welding, aluminum alloys, aluminium, magnesium, parameters, modes, compound formation mechanism, heating temperature, conditional yield strength
References

 

1. Arbegast W. J. Friction stir welding after a decade of development. Welding Journal. 2006. No. 3. pp. 28–35.
2. Ishchenko A. Ya., Podelnikov S. V., Poklyatskiy A. G. Friction stir welding of aluminium alloys (review). Avtomaticheskaya svarka. 2007. No. 11. pp. 32–38.
3. Ding J. et al. Friction stir welding flies high at NASA. Welding Journal. 2006. No. 3. pp. 54–59.
4. Okamura H., Aota K., Ezumi M. Friction stir welding of aluminum alloy and application to structure. Journal of Japan Institute of Light Metals. 2000. No. 4. pp. 166–172.
5. Ovchinnikov V. V., Drits A. M., Malov D. V. Features of welding of alloy 1565ch sheets in cold-worked condition. Zagotovitelnye proizvodstva v mashinostroenii. 2014. No. 11. pp. 8–14.
6. Ovchinnikov V. V. Technological features of friction stir welding aluminium alloys. Mashinostroenie i inzhenernoe obrazovanie. 2016. No. 4. pp. 22–45.
7. Lanciotti A., Vitali F. Characterisation of friction welded joints in aluminium alloy 6082-T6 plates. Welding International. 2003. No. 8. pp. 624–630.
8. Drits A. M., Ovchinnikov V. V., Malov D. V. Two-pass friction stir welding of sheets from “1565chM” alloy. Naukoemkie tekhnologii v mashinostroenii. 2014. No. 6. pp. 36–42.
9. Drits A. M., Ovchinnikov V. V. Mechanical Properties of Welded Joints of 1565chNN Alloy Sheets. Tekhnologiya legkikh splavov. 2014. No. 12. pp. 32–39.
10. Hassan A. A. et al. Effect of welding parameters on nugget zone microstructure and properties in high strength aluminum alloy friction stir welds. Science and Technology of Welding and Joining. 2003. No. 4. pp. 257–268.
11. Malofeev S. S., Kulitskiy V. A. Structure and mechanical properties of welds of 1570S alloy, obtaining by friction stir welding. Metally. 2012. No. 5. pp. 94–99.
12. Drits A. M., Ovchinnikov V. V. Properties of joints of aluminum alloys sheets obtained by friction stir welding. Zagotovitelnye proizvodstva v mashinostroenii. 2015. No. 10. pp. 7–15.
13. Colegrove P. A., Shercliff H. R. Experimental and numerical analysis of aluminium alloy 7075-T7351 friction stir welds. Science and Technology of Welding and Joining. 2003. No. 5. pp. 360–368.
14. Ryazantsev V. I., Matsnev V. N., Konkevich V. Yu. Friction stir welding of deformed and alloyed aluminium alloys. Aviatsionnaya promyshlennost. 2004. No. 4. pp. 33–36.
15. Ovchinnikov V. V., Drits A. M., Malov D. V. Mechanical properties of welded joints of alloys 1565chM and 1460T1 in various combinations obtained by friction stir welding. Zagotovitelnye proizvodstva v mashinostroenii. 2015. No. 6. pp. 11–17.
16. GOST 6996–66. Welded joints. Methods of mechanical properties determination. State Standard. Introduced: 1967–01–01.

 

Language of full-text russian
Full content Buy
Back