Journals →  Eurasian mining →  2017 →  #2 →  Back

EQUIPMENT AND MATERIALS
ArticleName Stress distribution analysis of PDC drill bits by computer modeling
DOI 10.17580/em.2017.02.06
ArticleAuthor Beshenkov P. S., Polushin N. I., Gkhorbani S., Sorokin E. N.
ArticleAuthorData

Engineering Ceramics Plant, Aprelevka, Russia:

Beshenkov P. S., Technologist

 

National University of Science and Technology—MISIS, Moscow, Russia:
Polushin N. I., Associate Professor, Candidate of Engineering Sciences, Head of Superhard Materials Research Laboratory
Gkhorbani S., Lecturer, Candidate of Engineering Sciences, siamak.ghorbani@misis.ru
Sorokin E. N., Senior Researcher

Abstract

Bits equipped with polycrystalline diamond compact (PDC) cutters are used in different purpose drilling in soft, medium-hard and, sometimes, hard rocks. The drill bit load, speed and torque, as well as density and cutting angles of cutters influence the PDC drilling efficiency. Improvement of drilling performance is one of the top priority economic goals. Production drilling is faced with a lot of technical problems to be solved to ensure high quality and efficiency of drilling. One of the predominant objectives of drilling is to select the best drill bit and to determine optimal drilling parameters as they directly govern the hole drilling cycle, the drill bit life, as well as the time and cost of drilling. Stresses in the body and cutting elements affect the behavior and productivity of PDC drill bits, as well as the running characteristics and failure-tolerance of cutters. High stresses can induce separation of the diamond compact top from the tungsten carbide substrate and initiate microcracks in the diamond layer. The microcracks grow and promote critical degradation of cutting tools in the course of drilling. The specified problems are commonly solved using software programs such as Solidworks Simulation, that make it possible to perform strength analysis, to obtain stress distribution patterns and to account for the influence exerted by angles of attack of PDC cutters on their stress state. This study is focused on stress distribution in cutting elements of PDC drill bits. The forces applied to the cutting elements of PDC drill bits are determined in the normal conditions and under critical impact loading. The effect exerted by the angles of attack of PDC cutters on the stress distribution and magnitude in drill bits is revealed.
This study has been carried out in the framework of the Federal Targeted Program on R&D in Priority Areas of Advancement in the Science and Technology of Russia for 2014–2020 in accordance with the Project on Development of the Technology for Production of Nanostructure Materials for Load-Bearing Substrates with High Impact Strength under the Grant Agreement No. 14.579.21.0093 dated July 27, 2015 (Unique Agreement Identifier FMEFI57915X0093) within the Integrated Project on the Technology of High-Efficient Horizontal and Inclined Drilling Bits for Oil and Gas Industry.

keywords Drill bit, drilling, PDC cutter, diamond and tungsten carbide plate, mechanical stress, cutting angle, computer modeling
References

1. Neskoromnykh V. V., Borisov K. I. Analytical investigation of the process of cutting and shearing of rock by the bit with PDC cutters. Izvestiya Tomskogo politekhnicheskogo universiteta. 2013. Vol. 323, No. 1. pp. 191–195.
2. Bugakov V. I., Laptev A. I. Manufacturing technology of drill bits under high pressure and temperature with the application of new diamond materials. Izvestiya vuzov. Chernaya metallurgiya. 2017. Vol. 60, No. 1. pp. 36–42.
3. Maslov A. L., Markova I. Yu., Zakharova E. S., Polushin N. I., Laptev A. I. Tribological tests of wear-resistant coatings used in the production of drill bits of horizontal and inclined drilling. IOP Conf. Series: Journal of Physics: Conf. Series, 2017. No. 857. pp. 1–5.
4. Polushin N. I., Ovchinnikova M. S., Sorokin M. N. Decrease of the content of metals in diamond layer of PCD polycrystals by chemical and electrochemical etching. Izvestiya VUZov “Poroshkovaya metallurgiya i funktsionalnye pokrytiya”. 2017. No. 2. pp. 31–38.

5. Tian J., Chuanhong F., Yang L., Yang Z., Pang X., You L., Zhu Y., Liu G. The Wear Analysis Model of Drill Bit Cutting Element with Torsion Vibration. Advances in Mechanical Engineering. 2014. Vol. 7, No. 1. pp. 1–9.
6. Kanyanta V., Ozbayraktar S., Maweja K. Effect of manufacturing parameters on polycrystalline diamond compact cutting tool stress-state. International Journal of Refractory Metals and Hard Materials. 2014. No. 45. pp. 147–152.
7. Kuftyrev R. Yu., Polushin N. I., Kotelnikova O. S., Laptev A. I., Sorokin M. N. Wear resistance of PCD composites used to complete PDC drill bits. Izvestiya vuzov. Chernaya metallurgiya. 2017. No. 9. pp. 52–61.
8. Belnap D., Griffo A. Homogeneous and structured PCD/WC-Co materials for drilling. Diamond and Related Materials. 2004. No. 13. pp. 1914–1922.
9. Borisov K. I. Dynamics of cutters operation during the rock failure by the cutting and shearing instruments PDC. Izvestiya Tomskogo politekhnicheskogo universiteta. 2010. Vol. 318, No. 1. pp. 161–164.
10. Jianhong F., Kexiong S., Zhi Z., Dezhi Z., Fei L., Xin X., Xin Z. Stress analysis on drilling string vibration in gas drilling. Energy Procedia. 2012. No. 16. pp. 1264–1268
11. Paggett J. W., Drake E. F., Krawitz A. D., Winholtz R. A., Griffin N. D. Residual stress and stress gradients in polycrystalline diamond compacts. International Journal of Refractory Metals and Hard Materials. 2002. No. 20. pp. 187–194.
12. Yahiaoui M., Gerbaud L., Paris J.-Y., Denape J., Dourfaye A. A study on PDC drill bits quality. Wear. 2013. No. 298–299. pp. 32–41.
13. Zhu. H., Liu Q., Deng J. et al. Rock-breaking mechanism of rotary-percussive drilling. Journal of Basic Science and Engineering. 2012. No. 4. pp. 622–31.
14. Huang Z., Tan L., Jin X. et al. Mechanical analysis and incline design of percussion-rotary drill bit side teeth. Equipment for Geophysical Prospecting. 2007. No. 2. pp. 87–91.
15. Fu Y. The approach of improving the shatter-resistant capability of ball gear brazing head alloy teeth. Rock Drill Machine Pneumatic Tools. 1988. No. 3. pp. 38–43.
16. Tan Z., Lai H. The failure analysis of ball tooth bit side tooth. Rock Drill Machine Pneumatic Tools. 1990. No. 3. pp. 17–24.
17. Polushin N. I., Laptev A. I., Baragunov E. M. Influence of the structure of diamond drill bits’ matrices on their abrasion resistance. Part 2. Research of wear resistance of diamond drill bits. Tsvetnye Metally. 2013. No. 2. pp. 72–75.
18. Ishbaev G. G., Vagapov S. Yu. Modern elements. Zhurnal Bureniya i Nefti. 2012. No. 6–7. pp. 44–46.
19. Gusman A. M. Ways of creation of efficient bits PDC for hard rock drilling. Vestnik Assotsiatsii burovykh podryadchikov. 2000. No. 1. pp. 28–32.

Full content Stress distribution analysis of PDC drill bits by computer modeling
Back