Journals →  CIS Iron and Steel Review →  2018 →  #1 →  Back

Metal Finishing
ArticleName Springback coefficient of round steel beam under elastoplastic torsion
DOI 10.17580/cisisr.2018.01.05
ArticleAuthor V. N. Shinkin
ArticleAuthorData

National University of Science and Technology “MISIS” (Moscow, Russia):

V. N. Shinkin, Dr. Sci. (Phys.-Math.), Prof., e-mail: shinkin-korolev@yandex.ru

Abstract

After the elastoplastic deformation of the metal structures and the metal products (for example, after a torsion, a bending, a compression, a stretching, the complex types of deformations), these bodies change their shape and partially springback. At the same time, the residual stresses arise in the bodies. Under the appropriate external conditions (for example, when the temperature changes), these stresses can lead to a significant distortion of the bodies’ shape (adopted after deformation) and even destroy these bodies. To estimate the residual shape of the round steel beam, which it takes after the mechanical deformation (the forming), it is necessary to know the springback coefficient of the round beam at the torsion. At the torsion of a round steel beam, the torques (the torsional moments, the twisting moments) also appear in the beam. This moments are connected with the tangential stresses in its cross-section. The maximum of the tangential stresses occur on the surface of the round beam and can lead to the destruction of the metal beam. However, even at very strong elastoplastic torsion around the symmetry axis of the beam, the tangential stress in the center of the cross-section of the round beam is zero and the elastic zone in the beam’s cross-section exists. Therefore, the destruction of the round steel beam and the defects of its metal under the torsion always start at the beam’s surface. The magnitude of the tangential stresses and angular deformations, their distribution along the cross-section of the round beam are always associated with the torque of the external forces. The greater the torque, the greater the tangential stresses and angular deformations. In this paper we have obtained the springback coefficient and the torques of the straight round beam under a torsion for an elastoplastic medium with a linear hardening, depending on the beam’s radius, the shear modulus, the yield strength and the hardening modulus of beam’s material. The research results can be used in the metallurgical and machine-building factories.

keywords Steel straight round beam, torsion of round beam, torque, tangential stress, crosssection of round beam, springback coefficient, elastoplastic deformation, continuous medium
References

1. Hu J., Marciniak Z., Duncan J. Mechanics of Sheet Metal Forming. Butterworth-Heinemann. 2002. 211 p.
2. Hu P., Ma N., Liu L.-Z., Zhu Y.-G. Theories, methods and numerical technology of sheet metal cold and hot forming. Analysis, simulation and engineering applications. Springer. 2013. 120 p.
3. Frank V. Lecture notes in production engineering. Springer. 2013. 211 p.
4. Calladine C. R. Plasticity for engineers. Theory and applications. Woodhead Publishing. 2000. 328 p.
5. Belskiy S., Mazur I., Lezhnev S., Panin E. Distribution of linear pressure of thin-sheet rolling across strip width. Journal of Chemical Technology and Metallurgy. 2016. Vol. 51. No. 4. pp. 371−378.
6. Belskiy S. M., Yankova S., Chuprov V. B., Bakhaev K. V., Stoyakin A. O. Temperature field of stripes under hot rolling. Journal of Chemical Technology and Metallurgy. 2015. Vol. 50. No. 6. pp. 613–616.
7. Belskiy S. M., Yankova S., Mazur I. P., Stoyakin A. O. Influence of the transversal displacements of metal on the camber formation of hot-rolled strip. Journal of Chemical Technology and Metallurgy. 2017. Vol. 52. No. 4. pp. 672−678.
8. Chakrabarty J. Theory of plasticity. Butterworth-Heinemann. 2006. 896 p.
9. Chakrabarty J. Applied plasticity. Springer. 2010. 758 p.
10. Klocke F. Manufacturing processes 1. Cutting. Springer. 2011. 506 p.
11. Klocke F. Manufacturing processes 4. Forming. Springer. 2013. 516 p.
12. Shinkin V. N. Calculation of steel sheet’s curvature for its flattening in the eight-roller straightening machine. Chernye Metally. 2017. No. 2. pp. 46−50.
13. Shinkin V. N. Calculation of bending moments of steel sheet and support reactions under flattening on the eight-roller straightening machine. Chernye Metally. 2017. No. 4. pp. 49–53.
14. Mikhailov A. M., Zubarev K. A., Kotel’nikov G. I., Semin A. E., Grigorovich K. V. Vaporization of the components of nickel alloys in a vacuum induction furnace. Steel in Translation. 2016. Vol. 46. No. 1. pp. 26–28.
15. Kuznetsov M. S., Yakushev E. V., Kulagin S. A., Kotel’nikov G. I., Semin A. E., Chegeliya R. K. Effect of the charge composition on the nitrogen content in a metal during steelmaking in an ASF using a solid charge. Russian Metallurgy (Metally). 2011. Vol. 2011. No. 12. pp. 1101–1105.
16. Korostelev A. A., Kotelnikov G. I., Semin A. E., Bozheskov A. N. Analysis of HBI effect in charge on technological parameters of EAF melting. Chernye Metally. 2017. No. 10. pp. 33–40.
17. Tursunov N. K., Semin A. E., Kotelnikov G. I. Kinetic features of desulphurization process during steel melting in induction crucible furnace. Chernye Metally. 2017. No. 5. pp. 23–29.
18. Tursunov N. K., Semin A. E., Sanokulov E. A. Study of dephosphoration and desulphurization processes in the smelting of 20GL steel in the induction crucible furnace with consequent ladle treatment using rare earth metals. Chernye Metally. 2017. No. 1. pp. 33–40.
19. Shinkin V. N. Asymmetric three-roller sheet-bending systems in steel-pipe production. Steel in Translation. 2017. Vol. 47. No. 4. pp. 235–240.
20. Shinkin V. N. Failure of large-diameter steel pipe with rolling scabs. Steel in Translation. 2017. Vol. 47. No. 6. pp. 363–368.
21. Shinkin V. N. Simplified calculation of the bending torques of steel sheet and the roller reaction in a straightening machine. Steel in Translation. 2017. Vol. 47. No. 10. pp. 639–644.
22. Lopatenko A. D., Orekhov D. M., Semin A. E. Improving the production of pipe steel. Steel in Translation. 2016. Vol. 46. No. 11. pp. 771–775.
23. Zubarev K. A., Kotel’nikov G. I., Titova K. O., Semin A. E., Mikhailov M. A. Predicting the liquidus temperature of complex nickel alloys. Steel in Translation. 2016. Vol. 46. No. 9. pp. 633–637.
24. Lim Y., Venugopal R., Ulsoy A. G. Process control for sheet-metal stamping process modeling, controller design and stop-floor implementation. Springer. 2014. 140 p.
25. Lin J., Balint D., Pietrzyk M. Microstructure evolution in metal forming processes. Woodhead Publishing. 2012. 416 p.
26. Belskiy S. M. Parameters of evaluation of shape cross section of hot-rolled steel strips. Message 1. The determination coefficient. Chernye Metally. 2017. No. 10. pp. 65–70.
27. Belskiy S. M. Parameters of evaluation of shape cross section of hot-rolled steel strips. Message 2. The saddle coefficient. Chernye Metally. 2017. No. 11. pp. 42−47.
28. Qin Y. Micromanufacturing engineering and technology. William Andrew. 2015. 858 p.
29. Hingole R. S. Advances in metal forming. Expert system for metal forming. Springer. 2015. 116 p.
30. Shinkin V. N. Calculation of technological parameters of O-forming press for manufacture of large-diameter steel pipes. CIS Iron and Steel Review. 2017. Vol. 13. pp. 33−37.
31. Shinkin V. N. Mathematical model of technological parameters’ calculation of flanging press and the formation criterion of corrugation defect of steel sheet’s edge. CIS Iron and Steel Review. 2017. Vol. 13. pp. 44−47.
32. Predeleanu M., Gilormini P. Advanced methods in materials processing defects. Vol. 45. Elsevier Science, 1997. 422 p.
33. Predeleanu M., Ghosh S. K. Materials processing defects. Vol. 43. Elsevier Science. 1995. 434 p.
34. Lenard J. G. Metal Forming Science and Practice. Elsevier Science. 2002. 378 p.
35. Shinkin V. N. Arithmetical method of calculation of power parameters of 2N-roller straightening machine under flattening of steel sheet. CIS Iron and Steel Review. 2017. Vol. 14. pp. 22−27.
36. Shinkin V. N. Springback coefficient of the main pipelines’ steel large-diameter pipes under elastoplastic bending. CIS Iron and Steel Review. 2017. Vol. 14. pp. 28−33.
37. Rees D. Basic engineering plasticity. An introduction with engineering and manufacturing applications. Butterworth-Heinemann. 2006. 528 p.
38. Wilko C. E. Formability. A review of parameters and processes that control, limit or enhance the formability of sheet metal. Springer. 2011. 112 p.
39. Davim J. P. Materials Forming and Machining. Research and Development. Woodhead Publishing. 2015. 202 p.

Full content Springback coefficient of round steel beam under elastoplastic torsion
Back