Журналы →  Tsvetnye Metally →  2018 →  №8 →  Назад

METAL PROCESSING
Название Investigation of ball milling and classification of coarse-grained tungsten carbide powders
DOI 10.17580/tsm.2018.08.13
Автор Avdeenko E. N., Zamulaeva E. I., Zaitsev A. A.
Информация об авторе

National University of Science and Technology “MISIS”, Moscow, Russia:
E. N. Avdeenko, Engineer of Scientific-Education Center of SHS, e-mail: avdeenko.misis@mail.ru
E. I. Zamulaeva, Research scientist of Scientific-Education Center of SHS
A. A. Zaitsev, Senior research scientist of Scientific-Educational Center of SHS

Реферат

Ultra-coarse-grained WC - Co hardmetals with WC grain size 5 μm are currently the materials of choice in rock drilling as possess higher wear resistance compared to that of fine-grained or medium-grained alloys having an equivalent hardness. In this study, we conducted a series of processes aimed at deagglomeration of ultra-coarse-grained tungsten carbide powder in a ball mill in different experimental modes. Two drum rotation speeds (“the rolling” and “the waterfall” modes) at two ratios between the weights of the grinding media and the powder (2:1 and 5:1) were studied; five different milling durations were used for each drum rotation speed and each ratio. The powder morphology and structure were studied by optical and scanning electron microscopies in the entire experimental design matrix. The optimal deagglomeration mode (5:1, nwaterfall = 64 rpm, milling time, 10 h) was determined by calculating the agglomeration index, which is equal to the ratio between the average agglomerate size and the average size of a monocrystal, and by measuring the granulometric composition of the powders, with the target 5–15 μm fraction isolated. In this mode, the percentage of the target fraction is 50 %, while the percentage of grains > 15 μm in size is 4%. The optimal mode of centrifugal air separation was selected: rotor speed = 3330 min–1 and the number of powder passage = 7 cycles. The powder was monocrystalline tungsten carbide with the percentage of the 5–15 μm fraction >95%. The WC grain size was maintained constant during subsequent mixing of tungsten carbide with cobalt. In the sintered WC – 6 % Co hardmetal >90% carbide grains belong to the size range of 6–13 μm.
The work was carried out with the support of the Ministry of Education and Science of the Russian Federation, Agreement No. 14.575.21.0156, Project RFMEFI57517X0156, Federal Target Program of “Research and development in priority areas of the scientific and technological complex of Russia for 2014–2020”.

Ключевые слова Tungsten carbide, сentrifugal air separation, ball milling, deagglomeration, coarse grained hardmetals, granulometric composition of the WC powders, 5–15 μm fraction, morphology, structure
Библиографический список

1. Tretyakov V. I. Foundations of metal science and technology of production of sintered hard alloys. Moscow : Metallurgiya, 1976. 527 p.
2. Panov V. S., Chuvilin A. M., Falkovskiy V. A. Technology and properties of sintered hard alloys and products made from them. Moscow : Izdatelskiy dom MISiS, 2004. 462 p.
3. Fang Z. Z., Koopman M. C., Wang H. Cemented tungsten carbide hardmetal — an introduction. Ed.: V. K. Sarin. Comprehensive Hard Materials. Oxford : Elsevier Ltd, 2014. pp. 123–135.
4. Konyashin I., Ries B. Wear damage of cemented carbides with different combinations of WC mean grain size and Co content. Part II: laboratory performance tests on rock cutting and drilling. International Journal of Refractory Metals and Hard Materials. 2014. Vol. 45. pp. 230–237.
5. Su W., Wen Y., Zhang Q. Effects of Ni and Cu additions on microstructures, mechanical properties and wear resistances of ultra-coarse grained WC – 6Co cemented carbides. International Journal of Refractory Metals and Hard Materials. 2018. Vol. 70. pp. 176–183.
6. Li X., Liu Y., Liu B., Zhou J. Effects of submicron WC addition on structures, kinetics and mechanical properties of functionally graded cemented carbides with coarse grains. International Journal of Refractory Metals and Hard Materials. 2016. Vol. 56. pp. 132–138.
7. Gee M. G., Gant A., Roebuck B. Wear mechanisms in abrasion and erosion of WC/Co and related hardmetals. Wear. 2007. Vol. 263. pp. 137–148.
8. Konyashin I., Schäfer F., Cooper R., Ries B., Mayer J., Weirich T. Novel Ultra-Coarse Hardmetal Grades with Reinforced Binder for Mining and Construction. International Journal of Refractory Metals and Hard Materials. 2005. Vol. 23. 225 p.
9. Roebuck B. Extrapolating hardness-structure property maps in WC/Co hardmetals. International Journal of Refractory Metals and Hard Materials. 2006. Vol. 24. pp. 101–108.
10. Dong-Yeol Y., Suk-Joong L. Kang Suppression of abnormal grain growth in WC – Co via pre-sintering treatment. International Journal of Refractory Metals and Hard Materials. 2009. Vol. 27. P. 90–94.
11. Schreiner M., Schmitt Th., Lassner E., Lux B. On the origin of discontinuous grain growth during liquid phase sintering of WC – Co cemented carbides. Powder Met. Int. 1984. Vol. 16. pp. 180–183.
12. Nie H., Zeng Q., Zheng J., Wen X., Yu Y. The preparation, preparation mechanism and properties of extra coarse-grained WC – Co hardmetals. Metal Powder Report. 2017. Vol. 72, Iss. 3. pp. 188–194.
13. TU 2631-003-05807999–98. Hexane. Introduced: 01.01.1998.
14. GOST 23148. Powders used in powder metallurgy. Sample selection. Introduced: 12.10.1998.
15. ISO 13320. Particle size analysis — Laser diffraction methods. 2009.
16. Libenson G. A., Lopatin V. Yu., Komarnitsky G. V. Processes of powder metallurgy. In 2 volumes. Vol. 1. Production of metal powders: a textbook for high schools. Moscow : Izdatelskiy Dom MISIS, 2001. 368 p.
17. Krasnova G. L., Gorbacheva T. B., Nikolskaya G. M., Rakoch T. A. Granulometric composition of tungsten carbide powders after long grinding. Theory and practice of production and application of hard alloys: scientific works. VNIITS. Moscow : TsNIItsvetmet ekonomiki i informatsii, 1991. pp. 3–7.

Language of full-text русский
Полный текст статьи Получить
Назад