Journals →  Tsvetnye Metally →  2019 →  #1 →  Back

METAL PROCESSING
ArticleName Gas production ability of coatings used in low-pressure casting of car wheels
DOI 10.17580/tsm.2019.01.11
ArticleAuthor Illarionov I. E., Gilmanshina T. R., Bogdanova Т. А., Kosovich А. А.
ArticleAuthorData

Ulianov Chuvash State University, Cheboksary, Russia:

I. E. Illarionov, Head of the Department of Materials Science and Metallurgical Processes

 

Siberian Federal University, Krasnoyarsk, Russia:
T. R. Gilmanshina, Associate Professor at the Department of Casting, e-mail: gtr1977@mail.ru

А. А. Kosovich, Assistant Lecturer at the Department of Casting

 

KiK, Krasnoyarsk, Russia:
Т. А. Bogdanova, Head of Metallurgy Department

Abstract

Light-alloy wheels have a complex cross-sectional profile. It means that they can have hot points which may potentialy produce gas porosity. One of the factors that may cause gas porosity includes the gas production ability of parting coatings. This paper presents a comparative analysis of how the gas production ability of parting coatings may impact the quality of wheels produced by low-pressure casting. The gas production ability of the coatings in view was analysed by measuring the density of gases that occur at the temperature when the melt gets in contact with the coated mold. The analysis was performed in the TA Instruments SDT Q600 thermoanalyser integrated with a Fourier infrared spectrometer. The study helped understand the kinetics of gases produced by heat-coductive and heat-sealing coatings under rising temperature. The measured optical density indicate that, at the contact temperature, the layer of the KTP110 heat-conductive coating, which was developed by the Department of Casting of the Siberian Federal University, produces less gases than ist foreign counterpart – D1. A double decrease in the amount of produced gases is associated with a 20 % reduction in gas defects in low-pressure cast wheels. Under the same temperature conditions, i.e. 690–720 oC, the developed heat-sealing coating Zh160 shows a 25% lower gas production ability compared with the D2 coating. Further compositional modification would impy further reduction in gas production with no impact on the heat-sealing properties. Consequently, the use of parting coatings with a low gas production ability provides one of the effective and feasible solutions that can help eliminate gas defects in low-pressure castings.

keywords Low-pressure casting, cast wheels, gas production ability, gas defects, parting coating, chill mold, thermoanalyser
References

1. Kosovich A. A. Improved quality of aluminium alloy wheels which are lowpressure cast using new parting coatings : Doctoral dissertation. Krasnoyarsk : Siberian Federal University, 2017. 117 p.
2. Bekker M. B., Zaslavsky M. L., Ignatenko Yu. F. et al. Pressure casting. 3rd revised edition. Moscow : Mashinostroenie, 1990. 400 p.
3. Vinarcik E. J. High integrity die casting processes. Hoboken : John Wiley & Sons Inc., 2002. 256 p.
4. From foundryman to foundryman. Low-pressure casting machines. RALInfo system. Available at: http://www.ruscastings.ru/files/file325.pdf
5. Putin V. A., Kiryakov A. G. Trends in the design of light-alloy car wheels. Proceedings of the 65th international conference of the Association of Automotive Engineers. 2009. Vol. 5. pp. 107–116.
6. Guide to Aluminium Casting Alloys by Aleris. Grevenbroich : Aleris Recycling, 2011. 102 p.
7. Zhang B., Cockcroft S. L., Maijer D. M., Zhu J. D., Phillion A. B. Casting defects in low-pressure die-cast aluminum alloy wheels. JOM. 2005. Vol. 57, Iss. 11. pp. 36–43.
8. Paderin V. N., Abdulgazis D. U. Manufacturing of solid car wheels by lowpressure casting of aluminium alloys into molds with gypsum elements. Transactions of Crimean Engineering and Pedagogic University. Engineering Sciences. 2014. Iss. 43. pp. 66–71.
9. Guofa Mi, Xiangyu Liu, Kuangfei Wang, Hengzhi Fu. Numerical simulation of low pressure die-casting aluminum wheel. China foundry. 2009. Vol. 6, No. 1. pp. 48–52.
10. Brown J. R. Foseco Non-Ferrous Foundrymans Handbook. Oxford : Butterworth Heinemann, 1999. 296 p.
11. Lysenko T. V., Kreytser K. A., Parkhomenko E. A. Improved quality of low-pressure castings made of magnesium alloys. Proceedings of the 11th International Conference (26–28 May 2015, Zaporozhie). Ed. by O. I. Ponomarenko. Zaporozhie : ZTPP, 2015. 450 p.
12. Illarionov I. E., Bogdanova T. A., Gil’manshina T. R., Merkulova G. A., Bogdanov A. Y. Technology for Modifying Aluminum Alloys with Ultrafine Silicon. Metallurgist. 2018. Vol. 62, Iss. 5–6. pp. 476–481.
13. Tretyak S. P. Development and testing of the method for calculating the temperature regimes of pressure casting moulds aimed at achieving the design surface quality : Extended abstract of PhD dissertation. Moscow, 1994. 15 p.
14. Prstiс A., Aсimoviс-Pavloviс Z., Andriс L., Stojanoviс J. Zircon-based coating for the applications in lost foam casting process. Chemical Industry & Chemical Engineering Quarterly. 2012. Vol. 18, Iss. 4. pp. 587–593.
15. Borouni M., Niroumand B., Fathi M. H. Effect of a nano-ceramic mold coating on the fluidity length of thin-wall castings in Al4-1 alloy gravity sand casting. Materials and Technology. 2014. Vol. 48, Iss. 4. pp. 473– 477.
16. Hamasaiid A., Dargusch M. S., Davidson C. J., Tovar S., Loulou T., Rezai-Aria F., Dour G. Effect of mold coating materials and thickness on heat transfer in permanent mold casting of aluminum alloy. Metallurgical and Materials Transactions: A. 2007. Vol. 38, Iss. 6. pp. 1303–1316.
17. Illarionov I. E., Strelnikov I. A. Anti-penetration coatings for foundry molds and cores. Liteyshchik Rossii. 2016. No. 4. pp. 24–25.
18. Svarika A. A. Mold coatings. Moscow : Mashinostroenie, 1977. 216 p.
19. Efimov V. A., Anisovich G. A., Babich V. N. et al. Special casting techniques. Moscow : Mashinostroenie, 1991. 436 p.
20. Babkin V. G., Leonov V. V., Gilmanshina T. R., Stepanova T. N. Phase transformations in graphite coatings and their effect on surface cleanness of castings. Chernye Metally. 2017. No. 10. pp. 54–59.
21. Gilmanshina T. R., Koroleva G. A., Baranov V. N., Kovaleva А. А. The Kureyskoye deposit graphite mechano-thermochemical modification technology. Obogashchenie Rud. 2017. No. 4. pp. 7–11.
22. Illarionov I. E., Gilmanshina T. R., Kovaleva A. A., Kovtun O. N., Bratukhina N. A. Destruction mechanism of casting graphite in mechanical activation. CIS Iron and Steel Review. 2018. Vol. 15. pp. 15–17.
23. All about metal and its processing. Available at: http://mitalolom.ru/stati/page/72/
24. Mikhaltsov A. M., Pivovarchik A. A., Subota A. A. Gas production ability of parting coatings used in pressure die casting of aluminium alloys. Litiyo i Metallurgiya. 2010. No. 4 (58). pp. 85–88.
25. A. A. Kosovich, E. G. Partyko, T. A. Bogdanova, P. Yu. Barbitsky, S. I. Lytkina, A. Yu. Bogdanov, S. V. Melnikov. Parting coating for casting moulds. Patent RF, No. 2604163. Applied: 29.05.2015. Published: 10.12.2016. Bulletin No. 34.
26. Integrated thermoanalyser SDT Q600 by TA Instruments (USA). Available at: http://www.ruschembio.ru/Sovmewennyj-termoanalizator-SDT-Q600-firmy-TA-Instruments-USA/
27. Analysis of gases which occur during heating/decomposition of specimens in thermoanalysers (TGA, DTA, DSC) using a Fourier infrared spectrometer with TGA 100. Available at: http://granat-e.ru/fsm_tga-100.html

Language of full-text russian
Full content Buy
Back