Journals →  CIS Iron and Steel Review →  2019 →  #1 →  Back

Rolling and Heat Treatment
ArticleName Study of the effect of isothermal holding on parameters of graphite phase in indefinite chromium-nickel cast iron alloyed by nitrogen and vanadium
DOI 10.17580/cisisr.2019.01.05
ArticleAuthor K. N. Vdovin, D. A. Gorlenko, D. V. Kuryaev, N. A. Feoktistov
ArticleAuthorData

Nosov Magnitogorsk State Technical University (Magnitogorsk, Russia):

K. N. Vdovin, Dr. Eng., Prof., Dept. of Foundry Production and Material Processing, E-mail: kn.vdovin@gmail.com
D. A. Gorlenko, Cand. Eng., Senior Lecturer of Dept. of Foundry Production and Material, E-mail: gorldima@yandex.ru
N. A. Feoktistov, Cand. Eng., Associate Prof., Head of Dept. of Foundry Production and Material, E-mail: fna87@mail.ru

 

Magnitogorsk Plant of Rolling Rolls (Magnitogorsk, Russia):

D. V. Kuryaev, Director

Abstract

The paper presents the effect of isothermal annealing at the temperatures higher than the temperature of carbide phase graphitization in indefinite cast iron on quantitative and qualitative parameters of graphite inclusions, depending on vanadium content and nitrogen presence in the alloy. This material is used for manufacture of the working layer of a dual-layered rolling roll. Absolute and relative variations of amount and average size of graphite inclusions are determined depending on the degree of alloy alloying in as-cast and heat treated states. Regularities of variation of graphite phase morphology depending on the degree of alloy alloying and presence of high-temperature heat treatment are examined.

keywords Dual-layered rolling rolls, working layer, indefinite cast iron, annealing, graphite, isothermal holding, nitrogen, vanadium
References

1. Martini F., Gostev K. A. New generation of wear-resistant bimetallic rolls for sheet mills. Metallurgist. 1999. Vol. 43. pp. 200-204.
2. Valeka T., Hampl J. Prediction of Metallurgic Quality of ICDP Material before Tapping. 2011 International Conference on Physics Science and Technology (ICPST 2011). Physics Procedia, 2011. Vol. 22. pp. 191–196.
3. Ray A., Prasad M. S., Dhua S. K., Sen K., Jha S. S. Microstructural features of prematurely failed hot-strip mill work rolls: Some studies in spalling propensity. Journal of Materials Engineering and Performance. 2000. Vol. 9. pp. 449–456.
4. Ray A., Prasad M. S., Barhai P. K., Mukherjee S. K. Metallurgical investigation of prematurely failed hot-strip mill workrolls: Some microstructural observations. Journal of Failure Analysis and Prevention. 2004. Vol. 4. pp. 58–66.
5. Nilsson M., Olsson M. Microstructural, mechanical and tribological characterization of roll materials for the finishing stands of the hot strip mill for steel rolling. Wear. 2013. Vol. 307. pp. 209–217.
6. Kanga Minwoo, Suhb Yongchan, Yong-Jun Ohc, Young-Kook Leea. The effects of vanadium on the microstructure and wear resistance of centrifugally cast Ni-hard rolls. Journal of Alloys and Compounds. 2014. Vol. 609. pp. 25–32.
7. Krüger J., von Schweinichen P., Mayr A., Mehlau S., Kaiser R. Modern technologies of work roll production for flat rolling. Chernye metally. 2017. No. 7. pp. 31–35.
8. Brander M., Elizondo L., Trickl T., Paar A., Hardt S. Optimization of rolls for hot rolling mills providing better efficiency. Chernye metally. 2017. No. 7. pp. 24–30.
9. Potapov A. I., Shestakova E. N., Orlov G. A., Belikov S. V. Usage of hyper-eutectoid steel grades for forging of work rolling rolls. Chernye metally. 2015. No. 2. pp. 33–37.
10. Asensio-Lozano J., Álvarez-Antolín J. F. Saturated Fractional Design of Experiments: Toughness and Graphite Phase Optimizing in Nihard Cast Irons. Journal of Materials Engineering and Performance. 2008. Vol. 17. pp. 216–223.
11. Asensio-Lozano J., Álvarez-Antolín J. F., Vander Voorth G. F. Identification and quantification of active manufacturing factors for graphite formation in centrifugally cast Nihard cast irons. Journal of Materials Processing Technology. 2008. Vol. 206. pp. 202–215.
12. Lecomte-Beckers J., Terziev L., Breier J.-P. Operating properties of rolling rolls made of graphite chromium cast iron. Stal. 2000. No. 1. pp. 46–50.
13. Kuskov Yu. M. Influence of graphite inclusions on service life of cast and deposited weld rolls for hot rolling. Stal. 2006. No. 2. pp. 41–45.
14. Ripocan I., Chicamera M. Influenta formei grafitului asupra comortarii la coc termic a fonte-lor cenucii. Metalurgia. 1981. Vol. 33. pp. 417–422.
15. Glover A. G., Pollard G. Deformation and Fracture of grey Cast-Iron Structures. J. Iron and Steel Institute. 1971. Vol. 209. pp. 138–141.
16. Liu Jinzhu, Man Yongfa. Development of abrasion-resistant Ni-hard 4 cast irons. Wear. 1993. Vol. 162-164. pp. 833–836.
17. Sunghak Lee, Do Hyung Kim, Jae Hwa Ryu, Keesam Shin. Correlation of microstructure and thermal fatigue property of three work rolls. Metallurgical and Materials Transactions: A. 1997. Vol. 28. pp. 2595–2608.
18. Liu Jinzhu, Li Shizhuo, Man Yongfa. Wear resistance of Nihard 4 and high-chromium cast iron re-evaluated. Wear. 1993. Vol. 166. pp. 37–40.
19. Vdovin K. N., Gorlenko D. A., Zavalischin A. N. Influence of industrial tempering on the composition of complex cast iron. Steel in Translation. 2013. Vol. 43. pp. 288–290.
20. Al-Rubaiea Kassim S., Pohlb M. Heat treatment and twobody abrasion of Ni-Hard 4. Wear. 2014. Vol. 312. pp. 21–28.
21. Vdovin K. N., Gorlenko D. A., Zavalischin A. N. Structure changes of chromium-nickel indefinite cast irons in heating. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta im. G. I. Nosova. 2013. No. 5 (45). pp. 9–11.

Full content Study of the effect of isothermal holding on parameters of graphite phase in indefinite chromium-nickel cast iron alloyed by nitrogen and vanadium
Back