Journals →  Tsvetnye Metally →  2020 →  #8 →  Back

LIGHT METALS AND CARBON MATERIALS
ArticleName Dynamics of formation and properties of cryolite-alumina crusts
DOI 10.17580/tsm.2020.08.07
ArticleAuthor Isaeva L. A., Mikhalev Yu. G., Zharinova N. Yu.
ArticleAuthorData

Siberian Federal University, Krasnoyarsk, Russia:

L. A. Isaeva, Associate Professor at the Department of Non-Ferrous Metallurgy, Candidate of Chemical Sciences
Yu. G. Mikhalev, Professor at the Department of Physical and Inorganic Chemistry, Doctor of Chemical Sciences, e-mail: y.mihalev@bk.ru
N. Yu. Zharinova, Associate Professor at the Geography Department1, Candidate of Biological Sciences

Abstract

This paper describes the results of an experimental study that looked at the cryolite-alumina crust formation rate. The density, strength and thickness of the obtained crusts were measured. Alumina from five different suppliers was used for crust formation. The paper describes physical and chemical properties of the alumina products used. Two types of alumina products are conventionally distinguished: A — the ones made in Russia and neighbouring countries; B — imported sandy alumina. The paper describes the experimental unit, as well as the experimental methods applied. Graphs are included showing the temperature-time relationship at different alumina fill levels. The obtained data were used to calculate the crust formation rate (V), the heat flow (Q) through the alumina crust and the heat conductivity of the crust (λк). The calculation technique is also described in the paper. Graphs are included that show the relationship between the molten electrolyte rise level in alumina fill and time for different types of alumina. There was observed an almost linear dependence of the electrolyte rise level on time, and the crust was growing continuously as long as it stayed in contact with electrolyte. It is shown that, as compared with type A aluminas, sandy aluminas (type B) form a cryolite-alumina crust 2–3 times quicker due to a quicker penetration of electrolyte. Because of the high concentration of α-Al2O3 and –45 μm particles in type A aluminas, the crusts formed with them are inferior to the ones formed with type B aluminas in terms of heat conductivity, thickness and strength. The obtained results can be used to calculate the heat losses occurring in cells through the cryolite-alumina crust. Process personnel can use the given data to interpret the reaction of the cell to a different type of alumina used.

keywords Alumina, cryolite-alumina crust, electrolyte, cell, cryolite ratio, temperature, heat flow, heat conductivity
References

1. Zhang Q. Thermochemical behaviour and stability of aluminium smelter crust. Auckland : University of Auckland, 2015.
2. Allard F., Désilets M., LeBreux M., Blais A. Chemical characterization and thermodynamic investigation of anode crust used in aluminum electrolysis cells. Light Metals. 2015. pp. 565–570.
3. Allard F., Désilets M., LeBreux M., Blais A. The impact of the cavity on the top heat losses in aluminum electrolysis cells. Light Metals. 2016. pp. 289–294.
4. Nikandrov K., Zarouni A., Akhmetov S., Ahli N. Evolution of crust breaker control for DX+ and DX+ ultra technologies. Light Metals. 2016. pp. 511–514.
5. Marinho D. C., Mourão M. B. Study of alumina dissolution in cryolitic bath to the vertical soderberg (VSS) aluminum production process. Light Metals. 2018. pp. 523–532.
6. Jassim A., Mofor E., Eddin J. W., Polle S. et al. Effect of changes in anode top cover composition on anode butt quality. Light Metals. 2018. pp. 1243–1251.
7. Wei S., Liu J., Ranaweera C., Groutso T. et al. Microstructure and properties analysis of aluminium smelter crust. Light Metals. 2019. pp. 779–785.
8. Isaeva L. A., Polyakov P. V. Alumina in aluminium production by electrolysis. Krasnoturyinsk : Izdatelskiy dom OAO “Bogoslovskiy alyuminievyi zavod”, 2000. 199 p.

9. Rye K. A. Alumina crusting in cryolitic melts. Part II: Bulk properties of crust. Light Metals. 1992. pp. 503–509.
10. All S. A., Gегlасh J., Hennig U. Vеrhаltеn von Рulverschiittungen aus Aluminiumoxiden in Fluoridschmelzen und Eigenshaften dег Reaktionsprodukte. Erzmetall. 1980. Vol. 33, No. 10. pp. 502–509.
11. Kheiri M., Gerlach J., Hennig U., Kammel R. Bildung und Yerhalten Vоn Krusten Sowie Boden Schlamm bei dеr Aluminium Reduktionselektrolyse. Erzmetall. 1987. Vol. 40, No. 3. pp. 127–131.
12. Rye K. A. Crust Formation in Cryolite Based Baths: Ph. D. thesis. Trondheim, 1992. 231 р.
13. Eggen T., Rolseth S., Rye K., Thonstad J. Alumina crusting in cryolitic melts. Part I: Penetration of molten electrolyte into alumina. Light Metals. 1992. pp. 495–502.
14. Less L. N. The сrusting bеhаviоuг of smelter aluminas. Metallurgical Transaction. 1977. Vol. 8B. pp. 219–225.
15. Townsed D. W., Boxall L. G. Crusting behavior of smelter аluminаs. Light Metals. 1984. pp. 649–665.
16. Buzunov V. Yu., Pecherskaya T. D., Tayanchin A. S. The quality and supply of alumina for RUSAL’s aluminium smelters. Non-Ferrous Metals of Siberia: 1st International Congress. 2009. pp. 248–253.
17. Skybakmoen E., Solheim A., Sterten A. Phase diagram for the system Na3AlF6 – AlF3 – Al2O3. Part II: Alumina solubility. Light Metals. 1990. pp. 317–323.
18. Kachanovskaya I. S., Siraev N. S., Pototskaya N. V. Dissolution of alumina in cryolite. Tsvetnye Metally. 1969. No. 9. pp. 64–66.
19. Isaeva L. A., Braslavskiy A. B., Polyakov P. V. Effect of the alpha-phase concentration and the size distribution on the rate of alumina dissolution in cryolite-alumina melts. Izvestiya vuzov. Tsvetnaya metallurgiya. 2009. No. 6.
pp. 35–40.

Language of full-text russian
Full content Buy
Back