JSC SPA Splav named after A.N. Ganichev, Tula, Russia:

A. N. Isaeva, Engineer

Tula State University, Tula, Russia:
S. N. Larin, Cand. Eng., Professor, Dept. of Mechanics of Plastic Forming, e-mail: mpf-tula@rambler.ru
V. I. Platonov, Cand. Eng., Associate Professor, Dept. of Mechanics of Plastic Forming
V. A. Korotkov, Cand. Eng., Associate Professor, Dept. of Mechanics of Plastic Forming

TA technique for construction of an experimental hardening curve based on the experience of compression of cylindrical specimens made of 11YuA steel is presented. The upsetting of specimens with 9 mm high and 5 mm in diameter was carried out on a R-5 testing machine with the recording of the “load-displacement” diagram. To reduce the influence of friction forces between the upset workpiece and the tool, the experiment was completed when the ratio of height to its diameter was equal to 1. This leads to a limitation of the range of the resulting strain intensity within 0.35 ... 0.45. To expand the boundaries of constructing the hardening curve, two composite samples obtained after the first upset were deformed, which made it possible to achieve a strain intensity of 0.75 ... 0.85 in each sample. Since the sample was compressed with the constant rate, the “load-displacement” graph was divided into several intervals, in which, in accordance with the displacement of the pressure plate, the cross-sectional area of the sample, deformation, load, and the corresponding stresses were determined. The set of obtained values of strain and stress intensities made it possible to plot the hardening curve of the studied material with subsequent approximation by a linear function. Hardening curves show that the nature of hardening of the material under study does not change as a result of a compressive test of a composite sample, therefore, contact friction forces do not affect the power parameters at significant strain rates. The proposed compression test method using a composite sample can significantly reduce the complexity of constructing a hardening curve and significantly expand the range of uniform deformation under uniaxial stress conditions.
The work was carried out within the framework of the RFBR grant No. 20-08-00401 A.

1. Yakovlev S. S. Forging and stamping: reference book. Vol. 4. Sheet stamping. Moscow: Mashinostroenie. 2010. 732 p.
2. Kolikov А. P., Romantsev B. А. Theory of metal forming. Moscow: MISiS. 2015. 451 p.
3. Hu P., Ma N., Liu L., Zhu Y. Theories, methods and numerical technology of sheet metal cold and hot forming: Analysis, simulation and engineering. London: Springer. 2013. 210 p.
4. Yakovlev S. P., Yakovlev S. S., Andreychenko V. А. Forming of anisotropic materials. Kishinev: Kvant, 1997. 331 p.
5. Uscinowicz R. Experimental study of the hardening process of Ti/Cu bimetal during compression test. Materials Today Communications. 2021. Vol. 28. p. 102687.
6. Shinkin V. N. Direct and inverse non-linear approximation of hardening zone of steel. Chernye Metally. 2019. No. 3. pp. 32–37.
7. Ding S., Khan S., Yanagimoto J. Metadynamic recrystallization behavior of 5083 aluminum alloy under double-pass compression and stress relaxation tests. Materials Science and Engineering: A. 2021. Vol. 822. p. 141673.
8. Khoddam S., Fardi M., Solhjoo S. A verified solution of friction factor in compression test based on its sample’s shape changes. International Journal of Mechanical Sciences. 2020. Vol. 193. p. 106175.
9. Platonov V. I., Chudin V. N., Romanov P. V. Pressure welding of shells with creep and plasticity. Russian Engineering Research. 2021. Vol. 41. No. 3. pp. 227–230.
10. Larin S. N., Platonov V. I., Korotkov V. А. The design of a matrix for drawing of materials processing planar anisotropy of mechanical properties. Tsvetnye Metally. 2018. No. 7. pp. 83–87.
11. Safronov A., Belsky S. M., Filatov A. Study of the microstructure of electrotechnical anisotropic steel with accelerated cooling. Procedia Manufacturing. 2019. Vol. 37. pp. 236–238.
12. Pasynkov А. А., Boriskin О. I., Larin S. N. Theoretical researches on operation of isothermal distribution of tubes from difficult-to-form non-ferrous alloys in conditions of a short-term creep. Tsvetnye Metally. 2018. No. 3. pp. 80–84.
13. Fadeev V., Kondrushin A. Special aspects of determining parameters for continuous deformation of pipe billets for the specified pipes size range. Materials Today: Proceedings. 2021. Vol. 38. pp. 1322–1325.
14. Goncharuk A. V., Fadeev V. A., Kadach M. V. Seamless pipes manufacturing process improvement using mandreling. Solid State Phenomena. 2021. Vol. 316. pp. 402–407.
15. Kukhar V. D., Malyshev А. N., Bessmertnaya Yu. V. Drawing low rectangular boxes from shaped billets. Chernye Metally. 2019. No. 1. pp. 39–42.
16. Shinkin V. N. Preliminary straightening of steel strip. Chernye Metally. 2018. No. 5. pp. 34–40.
17. Demin V. А., Chernyaev А. V., Platonov V. I., Korotkov V. А. Experimental technique for determining the mechanical properties of metal under stretching at high temperature. Tsvetnye Metally. 2019. No. 5. pp. 66–73.
18. Shinkin V. N. Simple analytical dependence of elastic modulus on high temperatures for some steels and alloys. CIS Iron and Steel Review. 2018. Vol. 15. pp. 32–38.
19. Chernyaev А. V., Usenko N. А., Korotkov V. А., Platonov V. I. Understanding how deformation rate influences the resistance to deformation under static tension at high temperature. Tsvetnye Metally. 2019. No. 5. pp. 60–66.
20. Larin S. N., Platonov V. I., Isaeva A. N., Romanov P. V. Manufacturing cylindrical articles with a thick bottom and thin wall. Chernye Metally. 2021. No. 5. pp. 63–67.
21. GOST 25.503–97. Design calculation and strength testing. Methods of mechanical testing of metals. Method of compression testing. Introduced: 01.07.1999. Moscow: Izdatelstvo standartov, 1997.
22. GOST 803–81. Hot-rolled strips of carbon high-grade steel for plating. Specifications. Introduced: 01.01.1983. Moscow: Izdatelstvo standartov, 1981.