Название |
Features of the stress-strain state of screw piercing of extra-thick-walled hollow billets for mechanical engineering |
Информация об авторе |
National University of Science and Technology “MISiS”, Moscow, Russia: S. M. Kriskovich, Senior Researcher, Dept. of Metal Forming, e-mail: moose2@yandex.ru V. P. Romanenko, Cand. Eng., Professor, Dept. of Metal Forming, e-mail: romanenko.vp@misis.ru N. M. Vavilkin, Dr. Eng., Professor, Dept. of Metal Forming
Vyksa Branch of the National University of Science and Technology “MISIS”, Vyksa, Russia: A. N. Fortunatov, Associate Professor |
Реферат |
Based on the previously developed model of the process of screw piercing of a particularly thick-walled workpiece, an analysis of its stressed and deformed state for feed angles of 6 and 12 degrees was carried out. The analysis of stress intensity parameters (SI) in twolongitudinal sections, as well as the parameters of strain rate intensity (SDI) and finite strain intensity (FSI) in cross sections was carried out. The SI distribution pattern in the longitudinal sections is very heterogeneous, the maximum stresses are observed at the mandrel toe and in the pinch region. The analysis of SDI showed its more correct distribution with maximum values in the nip, and also made it possible to identify the displacement of zones with the highest SDI value towards the point of contact between the workpiece and work rolls. The formation of an annular zone with low FSI values was revealed when analyzing the deformed state of the workpiece at higher feed angles, and a greater uniformity of the FSI field values at smaller angles, which can be used in the future to study the metal structure of the workpiece wall. |
Библиографический список |
1. Romanenko V. P., Stepanov P. P., Kriskovich S. M. Production of hollow railroad axles by screw piercing and radial forging. Metallurgist. 2018. Vol. 61. No. 9–10. pp. 873-877. 2. Xu Y., Zhang Y., Zhuang X., Cao Z., Lu Y., Zhao Z. Numerical modeling and anvil design of highspeed forging process for railway axles. International Journal of Material Forming. 2021. Vol. 14, Iss. 5. pp. 813–832. 3. Pokorný P., Dlhý P., Poduška J., Fajkoš R., Vojtek T., Náhlík L., Hutař P. Influence of heat treatment-induced residual stress on residual fatigue life of railway axles. Theoretical and Applied Fracture Mechanics. 2020. Vol. 109. p. 102732. 4. Goncharuk A. V., Fadeev V. A., Kadach M. V. Seamless pipes manufacturing process improvement using mandreling. Solid State Phenomena. 2021. Vol. 316. pp. 402–407. 5. Vavilkin N. М., Kriskovich S. М. Features of the stress state of screw piercing of especially thickwalled hollow billets for mechanical engineering. Chernye Metally. 2021. No. 10. pp. 44–48. 6. Surikova N. S., Vlasov I. V., Derevyagina L. S., Gordienko A. I., Narkevich N. A. Influence of cross-screw rolling modes on mechanical properties and fracture toughness of pipe steel. Izvestiya Ferrous Metallurgy. 2021 Vol. 64. No. 1. pp. 28–37. 7. Romantsev B. А., Aleshchenko А. S., Guseynov E. R., Tsyutsyura V. Yu. Development of a method and equipment for testing materials for alternating bending during piercing in screw rolling mills. Chernye Metally. 2020. No. 11. pp. 29–34. 8. Ding X., Sun L., Huang X., Zhao Z. Research on three-roll screw rolling process for Ti6Al4V titanium alloy bar. High Temperature Materials and Processes. 2019. Vol. 38. pp. 178–182. 9. Bogatov A. A., Pavlov D. A. Study of metal strained state during workpiece reduction in a three-roll screw-rolling mill. Metallurgist. 2017. Vol. 61, Iss. 3-4. pp. 311–317. 10. Mikhalkin D. V., Korsakov A. A., Panasenko O. A., Pyankov K. P. Parameters of the deformation zone and boundary conditions of the piercing process. Metallurgist. 2021. Vol. 65, Iss. 1-2. pp. 137–146. 11. Kulteshova V. V., Ivanov A. V., Zavora I. V., Lipatov R. N. Structure and mechanical properties of hot rolled hollow billets for body components of medium-carbon steels after piercing, sizing and sorbitization. Metallurgist. 2021. Vol. 65, Iss. 5-6. pp. 624–632. 12. Budnikov A. S., Romantsev B. A., Kharitonov E. A. Determination of rolls diameter for screwrolling mills. Izvestiya Ferrous Metallurgy. 2018. Vol. 61. No. 9. pp. 683–688. 13. Vlasov А. V., Stebunov S. А., Evsyukov S. А. Finite element modeling of technological processes of forging and die forging: textbook. Moscow: Izdatelstvo MGTU imeni N. E. Baumana, 2019. 383 p. 14. Vavilkin N. М., Bukhmirov V. V. Piercing mandrel. Moscow: MISiS. 2000. 128 p. 15. Orlov D. А. Improvement of the technology of double piercing of billets on screw rolling mills: Dissertation … of Engineering Sciences. Moscow. 2021. 113 p. |