Orenburg State University, Orenburg, Russia:

A. V. Tsukanov, Undergraduate, e-mail: 03-06-2000@mail.ru

South Ural State University (National Research University), Chelyabinsk, Russia¹ ; Novotroitsk branch of NUST MISIS, Novotroitsk, Russia²:

K. V. Litsin, Cand. Eng., Associate Prof. of Dep. "Electric Drive and Mechatronics"¹, Associate Prof. of Dep. "Electric Power and Electrical Engineering"², e-mail: k.litsin@rambler.ru

The article describes the development of an automated system for a batch cutting machine for rolling production. The use of an automated control system is substantiated, as well as the development of an automated control system that allows cutting 5 pipes diameter 40 mm at the same time. The rationale for the need to improve production efficiency by modernizing the algorithm of the machine and introducing new automation elements into its composition is presented. The analysis of the technological process of the batch cutting section was carried out. A functional diagram of automation has been developed. A description of each element of the functional diagram of automation and the purpose of its main functions are presented. The development of algorithms and visualization of the technological process of the automated system of the batch cutting machine was carried out. Modeling of a typical technological mode of operation of a batch cutting machine has been carried out. An automated system of a batch cutting machine has been developed, which makes it possible to increase the service life of circular saws by ensuring a uniform load on the teeth of a circular saw, with a general increase in production volumes. An estimate of capital costs has been compiled, maintenance and operation costs have been calculated after the introduction of the developed automated system. According to calculations, the developed automated system of the batch cutting machine will pay off in 2.8 years, and the profitability index is 1.07.

1. Rahman A., Sarker S., Islam M. T. Simulating Cutting Line of a Furniture Industry. International Conference on Production and Operations Management Society (POMS), 2018. pp. 1–7. DOI: 10.1109/POMS.2018.8629447.
2. Ai C., Jing W., Zhang H., Ze X., Zhao F. Research on precise locating control of large inertia ball mill. IEEE International Conference on Automation and Logistics, 2009. pp. 1634–1638. DOI: 10.1109/ICAL.2009.5262682.
3. Bannikov A. I., Makarova O. A., Shiryaev I. S., Osipov A. D. Investigation of heat distribution in the saw tooth, taking into account the periodicity of the process during stack cutting of cold rolled metal. Izvestiya Volgogradskogo gosudarstvennogo tekhnicheskogo universiteta. 2020. No. 8 (243). pp. 7–13. DOI: 10.35211/1990-5297-2020-8-243-7-13.
4. Long H. Adaptive control of cutting temperature for CNC machine tool. International Conference of Social Computing and Digital Economy (ICSCDE), 2021. pp. 51–55. DOI: 10.1109/ICSCDE54196.2021.00021.
5. Xia Z., Zhou K., Li X,. Cui X. A method of robot laser cutting for small holes. 9^th International Congress on Image and Signal Processing, BioMedical Engineering and Informatics (CISP-BMEI), 2016. pp. 1887–1891. DOI: 10.1109/CISP-BMEI.2016.7853025.
6. Uzlov O. V., Drozhevskaya A. V., Puchikov A. V., Grechka I. S. Increasing the service life of saw blades for cold metal cutting by heat treatment. Metaloznavstvo ta termichna obrobka metaliv. 2019. No. 4 (87). pp. 10–15. DOI: 10.30838/J.PMHTM.2413.241219.10.595.
7. Bannikov A. I., Makarova O. A., Shkurin I. K., Zeynalov D. R. Investigation of the stresses of a stack cutting saw. Izvestiya Volgogradskogo gosudarstvennogo tekhnicheskogo universiteta. 2020. No. 8 (243). pp. 14–18. DOI: 10.35211/1990-5297-2020-8-243-14-18.
8. GOST 8731-74. Steel seamless hot-deformed pipes. Technical requirements. Introduced: 01.01.1976.
9. GOST 8732-78. Steel seamless hot-deformed pipes. Dimension range. Introduced: 01.01.1979.
10. GOST R 53383-2009. Steel seamless hot-deformed pipes. Technical specifications. Introduced: 01.03.2010.
11. Setareh M., Parniani M., Aminifar F. An analytic methodology to determine generators redispatch for proactive damping of critical electromechanical oscillations. International Journal of Electrical Power and Energy Systems. 2020. No. 2. pp. 301–304.
12. Litsin K. V., Tsukanov A. V. Automated electric drive for the control system of a two-coordinate welding machine. Steel in Translation. 2021. Vol. 51. No 5. pp. 314–319. DOI: 10.3103/S0967091221050089.
13. Savsar M. A linear programming optimization model to minimize waste in cutting steel rods for table manufacturing. 3^rd International Congress on Human-Computer Interaction, Optimization and Robotic Applications (HORA), 2021. pp. 1–5. DOI: 10.1109/HORA52670.2021.9461270.
14. Bannikov A. I., Makarova O. A., Kovalev A. A., Shiryaev I. S. Investigation of the dependence of the contact length on the working stroke during stack cutting of cold rolled metal. Voprosy nauki i obrazovaniya. 2020. No. 21 (105). pp. 15–19.
15. Litsin K. V., Tsukanov A. V., Zhenenko A. I. Development of an Automatic System for Regulating Sinter Burden Moisture at JSC Ural Steel. International Conference on Industrial Engineering, Applications and Manufacturing (ICIEAM), 2021. pp. 557–560. DOI: 10.1109/ICIEAM51226.2021.9446371.
16. Bannikov A. I., Makarova O. A., Kovalev A. A., Osipov A. D. Investigation of the geometric parameters of burrs at the end of the pipe during stack cutting of cold rolled metal. Izvestiya Volgogradskogo gosudarstvennogo tekhnicheskogo universiteta. 2021. No. 1 (248). pp. 7–9. DOI: 10.35211/1990-5297-2021-1-248-7-9.
17. Wang Yu, Ding Guoqing, Ling Hangming, Yan Guozheng. The profile lining-cutting robot system based on offline program. Proceedings of IEEE Region 10 International Conference on Electrical and Electronic Technology. TENCON 2001 (Cat. No. 01CH37239). 2001. Vol. 2. pp. 597–600. DOI: 10.1109/TENCON.2001.949664.
18. Litsin K. V., Tsukanov A. V. Development of automated electric drive for the control system of two-coordinate welding machine. Izvestiya Ferrous Metallurgy. 2021. Vol. 64. No 5. pp. 382–388. DOI: 10.17073/0368-0797-2021-5-382-388.
19. Compact saw for billet cutting presented by Framag Industrieanlagenbau. Chernye Metally. 2017. No. 4. p. 15.