Журналы →  Gornyi Zhurnal →  2023 →  №10 →  Назад

MINERAL PROCESSING SOLUTIONS
Название Modeling autogenous milling of iron ore with regrinding of critical particle sizes
DOI 10.17580/gzh.2023.10.03
Автор Samukov A. D., Gerasimenko S. I.
Информация об авторе

RIVS Group, Saint-Petersburg, Russia

A. D. Samukov, Leading Production Engineer, A_Samukov@rivs.ru
S. I. Gerasimenko, Head of Ore Pretreatment Sector

Реферат

Reduction of capital and operating costs, and improvement of selectivity of mineral dissociation assumes the use of autogenous milling process at mines. While being caved, ore forms some particles of high strength, which resist impacting and possess no sufficient mass for finer milling. Accumulated in a mill, such particles worsen the mill productivity and increase the energy inputs. One of the main ways to prevent accumulation of difficult-tomill fraction is to remove it from a mill for the re-grinding. Due to complexity of full-scale testing of autogenous milling in semi-commercial quantity, it is increasingly popular to use simulation modeling in JKSimMet, which provides an integrated mathematical model of a milling cycle based on the studies of the physical and mechanical properties of test ore. For the simulation modeling and analysis, we selected iron ore (ferruginous quartzite). The modeling results show that the irretrievable removal of –70 +24 mm size is limited due to overcrowding of the mill by the finer sizes (–24 +1 mm) and by the capacity of the outlet grating of the mill. For an autogenous mill with the drum of 7×2.3 m, the limitation made 24–26 % of the initial feed in the cycle. In re-grinding down to the size of –5 mm with return to the milling cycle, the limitation grows to 55–58 % owing to the reduced size of the circulating fraction to –5 +0.63 mm. Depending on the amount of the small sizes to be removed, and on the selected process flow chart, the autogenous mill capacity in terms of the initial feed can be increased 1.1–2 times. The implemented research proves the relevance and high efficiency of the autogenous milling enhancement method with removal of small sizes from the mills for the further pebble milling, for the return in the milling cycle after re-grinding.

Ключевые слова Ore pretreatment, autogenous milling, intensification, ore pebble milling, small size grinding, critical size grinding, autogenous milling modeling
Библиографический список

1. Boduen A. Ya., Poperechnikova O. Yu., Zalesov M. V., Grigoryeva V. A. Experimental testing of technologies for processing refractory gold-bearing raw materials. Tsvetnye Metally. 2022. No. 7. pp. 24–32.

2. Saburbayeva L. Y., Yu P. S., Ukraintsev I. V., Boduen A. Y. Study of pressure oxidation and bacterial leaching efficiency as a method of refractory gold concentrate breakdown. IMPC 2018—29th International Mineral Processing Congress, 17–21 September 2018. Moscow : Canadian Institute of Mining, Metallurgy and Petroleum, 2019. pp. 2911–2921.
3. Yashin V. P., Bortnikov A. V. Theory and practice of autogenous milling. Moscow : Nedra, 1978. 229 p.
4. Sun W., Yang J., Li H., Liu W., Ma S. Differences in properties between pebbles and raw ore from a SAG mill at a zinc, tin-bearing mine. Minerals. 2022. Vol. 12(6). DOI: 10.3390/min12060774
5. Bortnikov А. V., Samukov А. D. Methodological approach to the choice of a rational technology and ore-preparation flow sheet. Obogashchenie Rud. 2010. No. 2. pp. 3–7.
6. Delboni H. Jr., Costa e Silva E., Alves V. K., Chieregati A. C. Pre-processing to increase the capacity of SAG mill circuits–Case study. Minerals. 2022. Vol. 12(6). DOI: 10.3390/min12060727
7. Bortnikov A. V., Samukov A. D. Vibration disintegration in ore-crushing at concentrators. Obogashchenie Rud. 2018. No 5. pp. 3–10.
8. Shipitsyna A. V., Gerasimenko S. I. Relevance of computer modeling in current practice of grinding cycle calculations. Gornaya promyshlennost. 2021. No. S5–2. pp. 24–28.
9. Chitalov L. S., Lvov V. V. Comparative assessment of the Bond Ball Mill Work Index tests. GIAB. 2021. Vol. 1. pp. 130–145.
10. Leung K. An energy based ore specific model for autogenous and semi-autogenous grinding : PhD. Thesis, University of Queensland, 1987.
11. Morrell S. Innovations in comminution modelling and ore characterization. Mineral Processing and Extractive Metallurgy: 100 Years of Innovation. 2014. pp. 77–90.
12. Chitalov L. S., Lvov V. V. New approaches in mineral raw materials comminution tests modeling. Advances in Raw Material Industries for Sustainable Development Goals. London : Taylor & Francis Group, 2021. pp. 146–151.

Language of full-text русский
Полный текст статьи Получить
Назад