Журналы →  CIS Iron and Steel Review →  2023 →  №2 →  Назад

Metal Science and Metal Physics
Название Optimal distribution of capsules with active substance for the crack detection system in a turbine blade body
DOI 10.17580/cisisr.2023.02.16
Автор I. K. Andrianov, E. K. Chepurnova
Информация об авторе

Komsomolsk-na-Amure State University (Komsomolsk-na-Amure, Russia)

I. K. Andrianov, Cand. Eng., Associate Prof., Aircraft Engineering Dept., e-mail: ivan_andrianov_90@mail.ru
E. K. Chepurnova, Graduate Student, Aircraft Engineering Dept., e-mail: el.chep@bk.ru


This research is devoted to optimization of the detection system for damages of blades of a gas turbine engine in
non-stationary conditions. The system is based on the approach on the method, when capsules with active substance are placed in a steel blade body, then a capsule is bursting due to difference of pressures during the process of crack propagation; as a result, ejected active substance is registered. The problem of this research is connected with optimal distribution of capsules, which contain active substance, in a turbine blade body. The research technique was developed for a modeling problem, when a steel turbine blade with constant cross section, having tensile crack and subjected to the action of extension centrifugal force, was observed. Development of the model with optimal distribution of capsules was based on assessment of pre-critical crack growth: it was required to distribute the capsules along the median line of blade cross section in such way, that it would be possible to detect the crack of pre-critical growth. Analysis of ultimate state of a blade with crack was carried out on the base of stress intensity coefficient, which allows to take into account the feature of crack location and to determine its critical length when its accelerated growth takes place. Variation of the pressure inside a capsule, required for its bursting depending on opening of crack sides. The suggested model takes into account location of the capsule with active substance relating to crack opening sides. Calculation of minimal number of capsules in blade bode depending on pressure inside the capsule and rotating speed of blades was conducted on the example of the steel turbine blade R-5530 B. The obtained dependences allow us to find the optimal combination between the geometric and physical characteristics of the crack detection system and the minimal number of capsules. The application of the proposed approach to the optimal distribution of capsules along the median line of the blade cross section will increase the efficiency of use of the damage detection system in turbine blades in non-stationary conditions, thereby ensuring the safety of operation of gas turbine engines in aviation technology.

This scientific research was carried out at the expense of the grant of the RF scientific fund No. 22-79-10114 «Development of the system for diagnostics the damages of turbine blades and the method of heat removal optimization in the conditions of thermal fatigue» (https://rscf.ru/project/22-79-10114/).

Ключевые слова Transverse separation crack, steel, turbine blade, stress state, damage detection system, cross section, gas turbine engines
Библиографический список

1. Kumar M., Heinig R., Cottrell M., Siewert Ch., Almstedt H., Feiner D., Griffin J. Detection of Cracks in Turbomachinery Blades by Online Monitoring. Journal of Engineering for Gas Turbines and Power. 2022. Vol. 20. p. 1830. DOI: 10.1115/1.4053705
2. Yang Laihao, Ma Meng, Wu Shuming, Chen Xuefeng, Yan Ruqiang, Mao Zhu. An improved analytical dynamic model for rotating blade crack: With application to crack detection indicator analysis. Journal of Low Frequency Noise, Vibration and Active Control. 2021. No. 40. p. 146134842110126. DOI: 10.1177/14613484211012602
3. Nowell D., Duo P., Stewart I. Prediction of fatigue performance in gas turbine blades after foreign object damage. International Journal of Fatigue. 2003. No. 25. pp. 963–969.
4. Rentala V. K., Mylavarapu P., Kumar A. POD of NDT Techniques Using High Temperature Oxidized Fatigue Cracks in an Aero Engine Alloy. J. Nondestr Eval. 2021. No. 40 (2). p. 41.
5. Rentala V. K., Mylavarapu P., Gautam J. P. Issues in estimating probability of detection of NDT techniques a model assisted approach. Ultras. 2018. Vol. 87. pp. 59–70. DOI: 10.1016/j.ultras.2018.02.012
6. Petukhov A. N., Kiselev F. D. Diagnostics of operating destructions in turbine blades of aircraft engines. Zavodskaya laboratoriya. Diagnostika materialov. 2019. Vol. 85. No. 3. pp. 41-51. DOI: 10.26896/1028-6861-2019-85-3-41-51

7. Kiselev F. D. Diagnostics of destructions and assessment of operating workability in operating turbine blades of aircraft engines. Мoscow: Izdatelstvo MATI. 2013. 296 p.
8. Lakshmi M. R. V., Mondal A. K., Jadhav C. K. Overview of NDT methods applied on an aero engine turbine rotor blade. Insight. 2013. Vol. 55 (9). pp. 482–486.
9. Kurz J. H., Jüngert A., Boller C. Reliability considerations of NDT by probability of detection (POD) determination using ultrasound phased array. Eng. Fail. Anal. 2013. Vol. 35. pp. 609–617. DOI: 10.1016/j.engfailanal.2013.06.008
10. Zhao R. G., Deng L. Y., Liu Y. F., Ji N., Ren C. L., Li X. M. Detection and analysis of high temperature fatigue fracture surface oxygen diffusion of GH4133B superalloy used in turbine disk of aero-engine. IOP Conf. Ser. Mater. Sci. Eng. 2019. 531. 012021.
11. Semenov A. S., Grishchenko A. I., Kolotnikov M. E., Getsov L. B. Finite element analysis of thermocyclic strength of gas turbine blades. Part 2. Calculation results. Vestnik Ufimskogo gosudarstvennogo aviatsionnogo tekhnicheskogo universiteta. 2019. Vol. 23. No. 2 (84). pp. 61-74.
12. Dubov A. A.. Matyunin V. M. Early diagnostics of damages of steam turbine blades using the method of magnetic metal memory. Teknologiya metallov. 2008. No. 5. pp. 41-44.
13. Shulzhenko N. G., Grishin N. N., Palkov I. A. Stress state of interlock of operating turbine blades. Problemy mashinostroeniya. 2013. Vol. 16. No. 3. pp. 37-45.
14. Getsov L. B., Semenov A. S., Semenov S. G. Providing of operating reliability of gas turbine units in compressor plants. Gazovaya promyshlennost. 2013. No. 5 (700). pp. 72-77.
15. Adamczuk R. R., Seume J. R. Early Assessment of Defects and Damage in Jet Engines. In: 2nd International Through-life Engineering Services Conference. 2013. Vol. 11. pp. 328–333.
16. Polyanskiy A. M., Polyanskiy V. M., Zaihyatulov I. I. On cracks formation in a turbine rotor blade after multiple testing. Trudy NPO Eneromash imeni alademika V. P. Glushko. 2007. No. 25. pp. 302-319.
17. Kashkarov A. M., Movchan Yu. V., Polyanskiy A. M. et al. On the causes of single cracks appearance on the blades of turbine working wheels. Trudy NPO Eneromash imeni alademika V. P. Glushko. 2006. No. 24. pp. 199-211.
18. Nott D. F. Basics of destruction mechanics. Мoscow: Metallurgiya. 1978. 256 p.
19. Morozov N. F. Mathematical problems of cracks theory. Мoscow: Nauka. 1984. 256 p.
20. Broek V. Basics of destruction mechanics. Мoscow: Vysshaya shkola. 1980. 368 p.
21. Hellan К. Introduction in destruction mechanics.Moscow: Mira. 1988. 364 p.
22. Nguen Ngok Т., Kolenko G. S. Analysis of destruction mechanics and workability of a gas turbine blade in presence of crack. Materialovedenie. Energetika. 2020. Vol. 26. No. 3. pp. 56-69. DOI: 10.18721/JEST.26304
23. Polyanskiy A. M., Polyanskiy V. M. Features of cracks growth in blades of nozzle plant in liquid propellant engine turbine. Trudy NPO Eneromash imeni alademika V. P. Glushko. 2014. No. 31. pp. 310-324.
24. Trebunskikh P. A. Building the mathematical model of defect appearance in turbine bladeor internal crack pump. Kontrol. Diagnostika. 2022. Vol. 25. No. 12 (294). pp. 20-25. DOI: 10.14489/td.2022.12.pp.020-025
25. Li Bing, Chen Lei, Wang Yuegen Gao, Mengqiu. 3D detection of internal defects for gas turbine blades. Insight - Non-Destructive Testing and Condition Monitoring. 2017. Vol. 59. pp. 364-370. DOI: 10.1784/insi.2017.59.7.364
26. Andrianov I. K., Grinkrug M. S., Vakuluk A. A. Numerical calculation of the heat sink parameters of the shell turbine vanes at the modeling of the heat-protective coating with a different number of layers. Lecture Notes in Networks and Systems. 2021. Vol. 200, pp. 37–46.
27. Kara Balli M., Grinkrug M. S. Technological research of parameters of the system for early detection of micro-cracks in an engine turbine blade. Production technologies of the future: from creation to putting into practice. Proceedings of the V International scientificpractical conference. Komsomolsk-na-Amure, December 06-11, 2021. Komsomolsk-na-Amure: Komsomolskiy-na-Amure gosudarstvennyi universitet. 2022. pp. 290-293.
28. Grinkrug M. S., Kara Balli M., Tkacheva J. I., Novgorodov N. A. Experimental study in order to choose an active substance in the early detection system of micro cracks in the turbine blade. IOP Conference Series: Materials Science and Engineering. 2021. March. 1111 012020.
29. Grinkrug M. S., Kara Balli M., Tkacheva Yu. I. The method of detection of micro-cracks in Komsomolsk-na-Amure: Komsomolskiy-na-Amure gosudarstvennyi universitet. 2019. Part 3. pp. 226-229.
30. Grinkrug M. S., Kara Balli M., Tkacheva J. I., Novgorodov N. A. An experimental bench for testing the cracks detecting technology in the blades of working aircraft engines. IOP Conference Series: Materials Science and Engineering. 2020. Vol. 734. p. 012022.
31. Pestrikov V. M., Morozov E. M. Mechanics of destructions. St. Petersburg. Professiya. 2012. 552 p.
32. Birger I. A., Shorr B. F., Iosilevich G. B. Strength calculation of machine components. Мoscow: Mashinostroenie. 1993. 640 p.
33. Deich M. E., Filippov G. A., Lazarev L. A. Atlas of profiles of axial turbines grids. Мoscow: Mashinostroenie. 1965. 96 p.

Полный текст статьи Optimal distribution of capsules with active substance for the crack detection system in a turbine blade body