Journals →  Gornyi Zhurnal →  2018 →  #2 →  Back

PHYSICS OF ROCKS AND PROCESSES
ArticleName Geomechanical evaluation of deep-level robotic coal mining by the results of numerical modeling
DOI 10.17580/gzh.2018.02.07
ArticleAuthor Pavlova L. D., Fryanov V. N.
ArticleAuthorData

Siberian State Industrial University, Novokuznetsk, Russia:

L. D. Pavlova, Director of the Institute of Information Technologies and Automation Systems, Doctor of Engineering Sciences, ld_pavlova@mail.ru
V. N. Fryanov, Head of a Chair, Doctor of Engineering Sciences

Abstract

It is of the current concern to develop a robotic technology for deep-level coal mining in the conditions of high methane content, gas-dynamic events and spontaneous firing. Such conditions increase rate of accidents which engender the health of miners. With a view to preventing accidents in coal mines, geomechanical evaluation of process requirements to be imposed on engineering, manufacture and introduction of robotic mining facilities for deep-level coal beds without the presence of personnel in hazardous areas has been accomplished. 3D numerical modeling is carried out with the finite element method and the author’s set of problemoriented programs. By the results of the simulation exercise, it is found that in the shortwall mining, the vertical subsidence of roof rocks grows almost linearly with the mining depth. The most hazardous areas in the shortwall roof are the junctures of breakage heading and rooms. The areas of maximum concentration of the vertical stresses in coal bed in the zone of operation of cutter–loader cutting head are detected. The stresses in these areas exceed coal compression strength, which allows utilizing energy of rock pressure to break coal at the minimal addition energy transfer to the cutting head, at the decreased amount of metal per structure of the robotic device and at the minimal energy consumption of coal extraction. The shortwall parameters and the process requirements applied to robotic systems of deep-level coal mining are substantiated.

keywords Roadway, initial cut, room, support, roof, modeling, stresses, robot, displacements, mine
References

1. Fryanov V. N., Pavlova L. D. Prospects of robotized mechanical-hydraulic gas-bearing coal pitchwork on the deep depths. Naukoemkie tekhnologii razrabotki i ispolzovaniya mineralnykh resursov. 2016. No. 2. pp. 19–27.
2. Salganik R. L., Mishchenko A. A., Fedotov A. A. Stress state in the vicinity of excavation in deep horizontal bed. Fiziko-tekhnicheskie problemy razrabotki poleznykh iskopaemykh. 2015. No. 2. pp. 24–33.
3. Yutyaev E. P. Present-day challenges and prospects of flat gas containing coal beds underground mining technology. Ugol. 2017. No. 5. pp. 30–36.
4. Erzhanov Zh. S., Saginov A. S., Gumenyuk G. N., Veksler Yu. S., Nesterov G. A. Creep flow of sedimentary rocks. Theory and experiment. Alma-Ata : Nauka, 1970. 208 p.
5. Hauquin T., Deck O., Gunzburger Y. Average vertical stress on irregular elastic pillars estimated by a function of the relative extraction ratio. International Journal of Rock Mechanics and Mining Sciences. 2016. Vol. 83. pp. 122–134.
6. Xiao Y.-X., Feng X.-T., Hudson J. A., Chen B.-R., Feng G.-L. et al. ISRM Suggested Method for In Situ Microseismic Monitoring of the Fracturing Process in Rock Masses. Rock Mechanics and Rock Engineering. 2016. Vol. 49, Iss. 1. pp. 343–369.
7. Bezukhov N. I. Basis of elasticity, plastic and plastic-flow theory. Second edition. Moscow : Vysshaya shkola, 1968. 512 p.
8. Shen B., Stephansson O., Rinne M. Modelling Rock Fracturing Processes. A Fracture Mechanics Approach Using FRACOD. Dordrecht : Springer, 2014. 173 p.
9. Pavlova L. D. Digitization of a massif of rocks on final elements, congruous to structural blocks destroyed coal massif. Vestnik Tomskogo gosudarstvennogo universiteta. 2004. No. 284. pp. 231–235.
10. Sainoki Atsushi, Mitri Hani S. Numerical investigation into pillar failure induced by timedependent skin degradation. International Journal of Mining Science and Technology. 2017. Vol. 27, Iss. 4. pp. 591–597.
11. Kornev E. S., Pavlova L. D. Finite element analysis software for solving the three-dimensional problems of mining geomechanics. Naukoemkie tekhnologii razrabotki i ispolzovaniya mineralnykh resursov. 2015. pp. 126–129.
12. Baskakov V. P., Rozenbaum M. A., Kalinin S. I., Sementsov V. V., Dobrovolskiy M. S. Thick seam mining unsafe gas-dynamic, system short working faces. Ugol. 2015. No. 11. pp. 17–20.
13. Available at: https://rosexpertpravo.ru/law/Data2/1/4293775/4293775200.pdf.
14. Available at: http://meganorm.ru/Data2/1/4293772/4293772185.htm.
15. Guide for the choice of frame yielding support of excavations. Second edition, revised and enlarged. Saint Petersburg, 1991. 125 p.
16. Liu X. S., Ning J. G., Tan Y. L., Gu Q. H. Damage constitutive model based on energy dissipation for intact rock subjected to cyclic loading. International Journal of Rock Mechanics and Mining Sciences. 2016. Vol. 85. pp. 27–32.
17. Zich A., Linnik Yu. N., Linnik V. Yu. Selecting Parameters of Cutter-Loader Drums for Specific Operating Conditions. Geo Resources Journal. 2015. No. 2. pp. 40–44.

Language of full-text russian
Full content Buy
Back