Journals →  Tsvetnye Metally →  2019 →  #5 →  Back

METAL PROCESSING
***
ArticleName Compacting as an efficient technique for upgrading the grinding swarf and ensuring environmental safety during its storage, transportation and metallurgical processing
DOI 10.17580/tsm.2019.05.09
ArticleAuthor Bespalov E. N., Kalmykov A. V., Matveev I. A.
ArticleAuthorData

Peter the Great St. Petersburg Polytechnic University, Saint Petersburg, Russia:

E. N. Bespalov, Postgraduate Student
A. V. Kalmykov, Researcher, e-mail: alexkalmyk@mail.ru
I. A. Matveev, Associate Professor

Abstract

This paper describes a technique for preparing the precision alloy grinding swarf for pyrometallurgical processing through compacting with the application of calcium oxide binders. The specific properties of swarf – mainly strong mechanical bonds between microswarf and abrasive grains – and its relatively high price make this process cost-effective as there is no need to mechanically separate the abrasive from the metal. The processes involved are environmentally friendly, no chemical reagents are used so there is no need for waste neutralization. The process involves a cleaning stage (when the residual lubricoolant is removed) and the actual compacting followed by drying. There are no special transportation or storage requirements for the resultant semi-finished product. The material has acceptable mechanical strength and moisture retention properties which make it easy to store and utilise in metallurgy as it contains approximately 40% of metal. Due to the low density (~1.2 g/cm3), there is no risk that the attached moisture will interact with the metal when the material is heated in an induction furnace. By adding fluorspar, the authors managed to obtain fluid slag of the triple system Al2O3 – CaF2 – CaO. Fluorspar was added after soaking to ensure there was no residual attached moisture in the material. A series of experiments was conducted with the metal mark YuN14DK24 (Fe-based alloy, consist Al, Ni, Cu and Co, till 24 mas. %) grinding swarf in an induction furnace with a graphite crucible. To prove the efficiency of metallurgical processing for waste treatment, the authors did a balance heat with fine chemicals. No residual metal was found in the resultant slag indicating a high recovery ratio. Composition-wise, this slag appeared to be similar to the slags used in electroslag remelting process, which suggests that metallurgical processing of grinding swarf can be an almost waste-free process.

keywords Grinding swarf, compacting, lubricoolant, corundum, lime, fluorspar, slag, induction furnace
References

1. Karimova A. A. Disposal of metallurgical lubricoolants. Modern Research – 2017 : Proceedings of international conferences. Neftekamsk : Mir nauki, 2017. pp. 626–634.
2. Matinde E., Simate G. S., Ndlovu S. Mining and metallurgical wastes: a review of recycling and re-use practices. Journal of the Southern African Institute of Mining and Metallurgy. 2018. Vol. 118, No. 8. pp. 825–844.
3. Lis T., Nowacki K., elichowska M., Kania H. Innovation in metallurgical waste management. Metalurgija. 2015. Vol. 54, No. 1. pp. 283–285.
4. Grinding dust (powder) as the product of ferrous and non-ferrous metal grinding. KlassInform : Book of Russian classifier codes. Available at: https://classinform.ru/fkko-2017/36122550000.html (Accessed: 19.03.2019).
5. Bukin V. I., Igumnov M. S., Safonov V. V., Safonov Vl. V. Recycling of production waste and secondary materials containing rare, precious and non-ferrous metals. Moscow : Delovaya stolitsa, 2002. 224 p.
6. Kayak G. L., Fomenko V. S., Andreev V. V. Developing a disposal process for the disposal of grinding swarf. The Far Eastern Federal University: School of Engineering Bulletin. 2017. No. 1. pp. 60–67.
7. Sokolov V. M., Fedorenko I. V. Enhanced refining technique for slag and Alnico grinding waste. Casting Processes. 2001. No. 3. pp. 81–84.
8. Birol B., Saridede M. N. Estimating the density of molten CaF2–Al2O3–CaO slags based on optical basicity. Minerals & Metallurgical Processing. 2016. Vol. 33, No. 2. pp. 82–87.
9. Burak B., Polat G. P., Saridede M. N. Estimation Model for Electrical Conductivity of Molten CaF2 – Al2O3 – CaO Slags Based on Optical Basicity. JOM. 2015. Vol. 67, No. 2. pp. 427–435.
10. Kalmykov A. V., Karasev V. P. Method of separation of multi-component material containing metallic components. Patent RF, No. 2201978. Published: 10.04.2003.
11. Semin A. E., Tursunov N. K., Kosyrev K. L. Innovative production of high-alloy steel and alloys. Theory and technology of induction furnace steelmaking. Moscow : MISiS, 2017. 166 p.
12. Vlasov A. A., Bazhin V. Yu., Pyaterneva A. A. Adsorptive ability of metallurgical alumina during the fluoride emission from cryolite melt surface. Tsvetnye Metally. 2015. No. 1. pp. 44–48.
13. Zatulovskiy S. S., Mudruk L. A. Production and application of clipped wire. Moscow : Metallurgiya, 1988. 183 p.
14. Sizyakov V. M., Bazhin V. Yu., Brichkin V. N., Petrov G. V. Metallurgy of non-ferrous metals. Saint Petersburg : Sankt-Peterburgskiy gornyy universitet, 2015. 392 p.
15. Popel S. I., Sotnikov A. I., Boronenkov V. N. Theory of metallurgical processes. Moscow : Metallurgiya, 1986. 463 p.
16. Slag Atlas : Reference book. Ed. by I. S. Kulikov. Moscow : Metallurgiya, 1985. 208 p.
17. GOST 30756—2001. Fluxes for electroslag technologies. General specifications. State standard. Introdiced 01.07.2005.

Language of full-text russian
Full content Buy
Back