Journals →  CIS Iron and Steel Review →  2020 →  #2 →  Back

Metal processing
ArticleName FEM study of internal stresses evolution in prestressing strands
DOI 10.17580/cisisr.2020.02.05
ArticleAuthor A. G. Korchunov, E. M. Medvedeva, P. V. Ivekeeva, D. V. Konstantinov
ArticleAuthorData

Nosov Magnitogorsk State Technical University (Magnitogorsk, Russia):

Korchunov A. G., Dr. Eng., Prof., Vice-Rector on International Affairs, E-mail: international@magtu.ru
Medvedeva E. M., Post-graduate Student, E-mail: fekla_med@mail.ru
Ivekeeva P. V., Post-graduate Student, E-mail: fufest01@mail.ru
Konstantinov D. V., Cand. Eng., E-mail: magstu.international@gmail.com

Abstract

This paper describes the results of modeling when the processes of stranding, reduction, straightening and thermo-mechanical treatment (TMT) of prestressing strands were simulated with the help of finite-element method. The distribution of residual stresses used in the simulation models refers to the stresses created at the preliminary stage of wire drawing. The simulation study looked at the effect of thermo-mechanical treatment on the internal wire stresses: residual stresses resultant from the drawing process and further stranding stresses. All studied methods demonstrated a positive effect not only in terms of eliminating internal stresses, but also from the point of view of their redistribution. Reduction of a strand in a solid tool at the ratios of 1–3 % allows to create tensile stresses at the surface of the wire and retain compressive stresses in its core. Straightening in a 5-roller group helped reach a double relaxation in outer wires. TMT, a process combining different physical effects, enabled to control within a broad range the redistribution of residual stresses in steel that was subjected to prior drawing at high deformation ratios. Such residual stresses occur as a result of stranding stresses that accompany the stranding operation and can affect the geometry of the strand. The study showed that tension as a TMT parameter plays a greater role in the elimination of longitudinal residual stresses. That’s why, at the minimum tension, almost no redistribution of residual stresses occur either in the central or in the near-surface layers irrespective of the TMT temperature regime applied. However, when the tension exceeding 70 kN is applied at the temperatures of 380–400 °C, the central and surface residual stresses balance off in the wire or almost disappear.

This research was carried out under the Decree No. 220 dated 9th April 2010 of the Government of the Russian Federation (Contract No. 075-15-2019-869 dated 12th May 2019) and was funded by the Russian Science Foundation (Project No. 20-69-46042 dated 20th May 2020) and by the Russian Ministry of Education and Science with the goal of developing high-tech production (contract nos. 02.G25.31.078, December 1, 2015; and MK204895, July 27, 2015).

keywords Prestressing strand, wire, drawing, thermo-mechanical treatment, finite-element modeling, residual stresses, internal stresses, stranding, straightening
References

1. Madatyan S. A. Current requirements to prestressing steel. Beton i zhelezobeton. 2005. No. 1. pp. 8–10.
2. Egorov V. D., Voronina V. S. Production of stabilized prestressing strands. Stal. 1983. No. 3. pp. 65—66.
3. Costello G. A. Theory of wire rope. Second edition. New York: Springer, 1997. 123 p.
4. Feyrer K. Wire ropes: tension, endurance, reliability. Berlin – Heidelberg – New York: Springer, 2007. 322 p.
5. Jacinto L., Pipa M., Oliveira Santos L. Probabilistic models for mechanical properties of prestressing strands. Construction and Building Materials. 2012. Vol. 36. pp. 84–89.
6. Aytaç Onur Yu. Experimental and theoretical investigation of prestressing steel strand subjected to tensile load. International Journal of Mechanical Sciences. 2016. Vol. 118. pp. 91–100.
7. Obaydullah M., Zamin Jumaat M., Johnson Alengaram U., Mahfuz ud Darain Kh., Nazmul Huda Md., Akter Hosen Md. Prestressing of NSM steel strands to enhance the structural performance of prestressed concrete beams. Construction and Building Materials. 2016. Vol. 129. pp. 289–301.
8. Mikhailov K. V. Challenges faced by the domestic construction science in the area of prestressed reinforced concrete structures. Beton i zhelezobeton. 2004. No. 2. pp. 3–5.
9. Chukin M. V., Gun G. S., Korchunov A. G., Polyakova M. A. Prospects of production of high-strength steel reinforced bars made of high-carbon steels. Chernye Metally. 2012. No. 12. pp. 8–16.
10. Chabbi L. Simulation of microstructure and mechanical properties in section rolling. Chernye Metally. 2017. No. 9. pp. 57—62.
11. Korchunov A. G., Gun G. S., Shiryaev O. P., Pivovarova K. G. Study of structural transformation of hot-rolled carbon billets for high-strength ropes for responsible applications via the method of thermal analysis. CIS Iron and Steel Review. 2017. Vol. 13. pp. 38–40.
12. Korchunov A. G., Polyakova M. A., Konstantinov D. V., Dabalá M. Mechanical properties of prestressing strands and how they tend to change under thermo-mechanical treatment. CIS Iron and Steel Review. 2019. Vol. 18. pp. 14–19.
13. Caballero L., Atienza J. M., Elices M. Thermo-mechanical treatment effects on stress relaxation and hydrogen embrittlement of cold-drawn eutectoid steels. Metals and Materials International. 2011. Vol. 17. No. 6. pp. 899–910.
14. Atienza J. M., Elices M., Ruiz-Hervias J., Caballero L., Valiente A. Residual Stresses and Durability in Cold Drawn Eutectoid Steel Wires. Metals and Materials International. 2007. Vol. 13. No. 2. pp. 139–143.
15. Atienza J. M., Elices M. Influence of residual stresses in the stress relaxation of cold drawn wires. Materials and Structures / Materiaux et Constructions. 2004. Vol. 37. June. pp. 301–304.
16. Elices M. Influence of residual stresses in the performance of cold-drawn pearlitic wires. Journal Of Materials Science. 2004. Vol. 39. pp. 3889–3899.
17. Atienza J. M., Ruiz-Hervias J., Elices M. The Role of Residual Stresses in the Performance and Durability of Prestressing Steel Wires. Experimental Mechanics. 2012. Vol. 52. pp. 881–893.
18. Atienza J. M., Ruiz-Hervias J., Martinez-Perez M. L., Mompean F. J., Garcia-Hernandez M., Elices M. Residual stresses in cold drawn pearlitic rods. Scripta Materialia. 2005. Vol. 52. pp. 1223–1228.
19. Martinez-Perez M. L., Mompean F. J., Ruiz-Hervias J., Borlado C. R., Atienza J. M., Garcia-Hernandez M., Elices M., Gil-Sevillano J., Ru Lin Peng, Buslaps T. Residual stress profiling in the ferrite and cementite phases of cold-drawn steel rods by synchrotron X-ray and neutron diffraction. Acta Materialia. 2004. Vol. 52. pp. 5303–5313.
20. Zheng Wenzhong, Hu Qiong, Zhang Haoyu. Experimental research on the mechanical property of prestressing steel wire during and after heating. Frontiers of Structural and Civil Engineering. China 2007.
21. Konstantinov D. V., Korchunov A. G., Zaitseva M. V., Shiryaev O. P., Emaleeva D. G. Macro- and Micromechanics of Pearlitic-Steel Deformation in Multistage Wire Production. Steel in Translation. 2018. Vol. 48. pp. 458–462.

Full content FEM study of internal stresses evolution in prestressing strands
Back