Journals →  Chernye Metally →  2021 →  #5 →  Back

Machine-building technologies
ArticleName Manufacturing of cylindrical articles with a thick bottom and thin wall
DOI 10.17580/chm.2021.05.11
ArticleAuthor S. N. Larin, V. I. Platonov, A. N. Isaeva, P. V. Romanov.

Tula State University (Tula, Russia):

S. N. Larin, Dr. Eng., Prof., Dept. “Mechanics of Plastic Shaping”, e-mail:
V. I. Platonov, Cand. Eng., Associate Prof.
P. V. Romanov, Student

Scientific and Production Union “Splav” named after A. N. Ganichev (Tula, Russia):

A. N. Isaeva, Engineer


The issue of increasing the efficiency of metal forming processes by combining the operations of drawing with thinning of the wall and extrusion in the manufacture of cylindrical articles having a thick bottom and thin wall. The ratio of height to diameter can vary from 1 to 10 and more. These are various connectins, adapters, unions, elements of cases, sleeves and other articles with a wall thickness less, than thickness of a bottom. Rolled sheet metal made of various grades of steel, brass, aluminum, titanium and other materials can be used as workpiece materials. The combination of drawing operations with wall thinning and extrusion at one working position allows to significantly expand the technological capabilities of metal forming, reduce the number of steps, improve the quality of articles. Compared to backward extrusion, the proposed technology provides a lower level of stress in the tool and workpiece, enabling to use less powerful hydraulic press equipment and significantly increase the durability of stamping equipment. When using blanks with planar anisotropy, this technology allows not only to eliminate earing on the edge surface of the semi-finished product and get a smooth face end of the product, but also to form any other profile of the edge of the part. The formation of articles without earing eliminates the operation of trimming the end face of the semi-finished product, which significantly increases the utilization of the material and reduces the cost of finished articles. The method for calculation of geometrical parameters of stamping equipment to obtain defect-free articles is given. Theoretical studies of the combination of drawing operations with thinning and extrusion of the cylindrical workpiece were carried out by the finite element modeling method using the QFORM software package. The scheme of universal experimental stamping equipment is shown.

keywords Drawing, extrusion, stresses, deformations, anisotropy, ears, combination of operations

1. Low-waste, resource-saving stamping technology. Editied by Andreychenko V. А., Yudin L. G., Yakovlev S. P. Kishinev: Universitas, 1993. 240 p.
2. Forging and stamping: Handbook: In 4 vols. Vol. 4. Sheet stamping Edited by Yakovlev S. S. Editorial board: Semenov Е. I. et. al. 2nd edition revised and enlarged. Moscow: Mashinostroenie, 2010. 732 p.
3. Storozhev М. V., Popov Е. А. Theory of metal forming. Moscow: Mashinostroenie, 1977. 423 p.
4. Nechepurenko Yu. G., Yakovlev S. P., Yakovlev S. S. Deep drawing of cylindrical articles from anisotropic material. Tula: TulGU, 2000. 195 p.
5. Popov Е. А. Fundamentals of sheet metal stamping theory. Moscow: Mashinostroenie, 1977. 278 p.
6. Yakovlev S. S., Tregubov V. I., Nechepurenko Yu. G. Deep drawing of anisotropic hardening material. Zagotovitelnye proizvodstva. 2005. No. 4. pp. 38–44.
7. Yakovlev S. P., Yakovlev S. S., Andreychenko V. А. Anisotropic materials forming. Kishinev: Kvant, 1997. 331 p.
8. Mousavia A., Kunzeb T., Rochb T., Lasagnib A., Brosius A. Deep drawing process without lubrication – an adapted tool for a stable, economic and environmentally friendly process. Procedia Engineering. 2017. Vol. 207. pp. 48–53.
9. Tennera J., Andreasa K., Radiusa A., Merklein M. Numerical and experimental investigation of dry deep drawing of aluminum alloys with conventional and coated tool surfaces. Procedia Engineering. 2017. Vol. 207. pp. 2245–2250.
10. Senyong Chen, Yi Qin, Chenb J. G., Chee-Mun Choy. A forging method for reducing process steps in the forming of automotive fasteners. International Journal of Mechanical Sciences. 2017. Vol. 137. pp. 1–14.
11. Jin J., Lei X. W., Luo D. J. A single-step hot stamping-forging process for aluminum alloy shell parts with nonuniform thickness. Journal of Materials Processing Technology. 2016. Vol. 228. pp. 170–178.
12. Larin S. N., Platonov V. I., Korotkov V. А. The design of a matrix for drawing of materials possessing planar anisotropy of mechanical properties. Tsvetnye Metally. 2018. No. 7. pp. 83–87.
13. Kukhar V. D., Kireeva А. Е., Pasko А. N. Theoretical and experimental investigations of forging the “case” details via extruding steel billets. Chernye Metally. 2018. No. 6. pp. 16–19.
14. Pasynkov А. А., Boriskin О. I., Larin S. N. Theoretical researches on operation of isothermal distribution of tubes from difficult-to-form non-ferrous alloys in conditions of a short-term creep. Tsvetnye Metally. 2018. No. 3. pp. 74–78.
15. Kukhar V. D., Malyshev А. N., Bessmertnaya Yu. V. Drawing low rectangular boxes from shaped billets. Chernye Metally. 2019. No. 1. pp. 39–42.
16. Demin V. А., Chernyaev А. V., Platonov V. I., Korotkov V. А. Experimental technique for determining the mechanical properties of metal under stretching at high temperature. Tsvetnye Metally. 2019. No. 5. pp. 66–73.
17. Chernyaev А. V., Usenko N. А., Korotkov V. А., Platonov V. I. Understanding how deformation rate influences the resistance to deformation under static tension at high temperature. Tsvetnye Metally. 2019. No. 5. pp. 60–65.
18. GOST 2590–2006. Round hot-rolled steel bars. Dimensions. Introduced: 01.07.2009.
19. Korotkov V. А., Larin S. N., Romanov P. V., Isaeva A. N. Die for drawing with thinning. Patent RF, No. 2705830. Applied; 19.07.2019. Published: 12.11.2019. Byulletin No. 32.

Language of full-text russian
Full content Buy