Joint-Stock Company “Inrau”, Chelyabinsk, Russia:

E. A. Maksimov, Head of Technical Department, Candidate of Techical Sciences, e-mail: maksimov50@mail.ru

Moscow Polytechnical University, Moscow, Russia:

R. L. Shatalov, Professor, Doctor of Technical Sciences, e-mail: mmomd@mail.ru

Kolchuginsky factory OTSM, Kolchugino, Russia:

E. A. Yudin, Chief Engineer, e-mail: udin73@mail.ru

It is shown that a main route of development of pressure treatment of non-ferrous metals is a heading of innovative designs in the manufacture, providing development of manufacture of new brands of alloys from brass metal and copper with demanded mechanical properties, including with high heat conductivity, and also the improved critical bucklings. Such properties tapes from brass metal and copper, and also their alloys with the improved critical bucklings possess. By manufacture of manufactured goods, and also by manufacture of the goods of mass demand (heat exchangers, pipes, radiators) are used cold rolling tapes from brass metal and copper. It is shown that questions of martempering of geometrical figures of merit of tapes from brass metal and copper, including formation of the transverse nonuniform thickness, a cross profile and the geometrical form of tapes, and also definition profiling rolls reversible four rolling mill and two rolling mill at cold rolling demand the development. It is installed that the major parametre of dimensional accuracy of tapes are nonflatness and the transverse nonuniform thickness, that is change of a thickness of a tape on its width. It is shown that on the form interstitial a positive allowance forming the transverse nonuniform thickness of tapes, following factors influence: an elastic bending flexure rolls, irregularity of flattening on length of the barrel rolls on work roll and hire contact, thermal convexity of barrels of shafts, deterioration of barrels rolls, a hydraulic bend rolling systems, the original transverse nonuniform thickness, profiling rolls. A traditional method of formation interstitial a positive allowance is profiling rolls which in huge extent influences a course of process of rolling and quality of metal products. Dependences for calculation rational profiling work rolls, and also an elastic bending flexure rolls on length of the barrel, equal width rolling tapes for the vacuum mill are presented. It is shown that at rolling of tapes from copper on the reversible two rolling mill 350×450 with use rational profiling rolls the deviation from planeness of ready tapes fulfils to acting specifications. At rolling of tapes from yellow metal on reversible four rolling a mils 150/500×400 with rational profiling rolls, the transverse nonuniform thickness of tapes of 1,00 mm matches in the thickness to the raised accuracy.

1. Raykov Yu. N. Production and consumption of rolled heavy non-ferrous metals. Fundamental problems. Innovative materials and technologies. OMD 2014. Proceedings of the international scientific and technical congress National University of Science and Technology “MISiS”, FSUE “TsNIIchermet named after I. P. Bardin”. Moscow, 2014. Vol. 1. pp. 59–60.
2. Raykov Yu. N. Trends in development of the Russian market for rolled products from copper and its alloys. Copper. Brass. Bronze: collection. Moscow : “JSC Institute Tsvetmetobrabotka”, 2006. pp. 332–340.
3. Raykov Yu. N., Ashikhmin G. V., Polukhin V. P., Gulyaev А. S. Copper alloys: reference book. Moscow : Tsvetmetobrabotka, 2011. 456 p.
4. Shatalov R. L. , Pruzhinin I. F., Mochalov N. А., Shimanaev А. Е. еt. al. Technologies and modes of rolling high-quality copper alloy strips for coins. Copper. Brass. Bronze: collection. Мoscow : Tsvetmetobrabotka, 2006. pp. 179–194.
5. Shatalov R. L. Improvement of quality of strips made of non-ferrous metals and alloys. Tsvetnye Metally. 2001. No. 5. pp. 65–70.
6 Tretyakov А. V., Garber E. А., Davletbaev G. G. Calculation and research of rolling rolls. Moscow : Metallurgiya, 1976. 266 p.
7. Maksimov Е. А., Shatalov R. L., Boskhamdzhiev N. Sh. Production of flatbed strips by rolling. Moscow : Teplotekhnik, 2008. 336 p.
8. Konovalov Yu. V. Calculation of sheet rolling parameters. Moscow : Metallurgiya, 1968. 429 p.
9. Tkalich К. N., Konovalov Yu. V. Precise rolling of thin strips. Moscow: Metallurgiya, 1972. 108 p.
10. Garber E. А. Production of rolled products: reference edition. Vol. 1. Book. 1. Production of cold-rolled strips and sheets (assortment, theory, technology, equipment). Moscow : Teplotekhnik, 2007. 368 p.
11. Shevakin Yu. F., Chernyshov V. N., Shatalov R. L, Mochalov N. А. Metal Forming. Moscow : Intermet, 2005. 496 p.
12. Tselikov А. I., Nikitin G. S., Rokotyan S. Е. Longitudinal rolling theory. Moscow : Metallurgiya 1980. 318 p.
13. Tretyakov А. V. Theory, calculation and research of cold rolling mills. Moscow : Metallurgiya, 1966. 255 p.
14. Polukhin V. P. Mathematical modeling and computer calculation of sheet rolling mills. Moscow : Metallurgiya, 1972. 512 p.
15. Kokhan L. S., Navrotskiy А. G. Mechanical equipment of workshops for production of non-ferrous metals. Moscow : Metallurgiya, 1985. 312 p.
16. Maksimov Е. А. The self-regulatory mechanism of process of asymmetric cogging for increase of the geometrical sizes and bar flatness improvement. Tsvetnye Metally. 2010. No. 1. pp. 89–92.
17. Polukhin P. I, Galkin А. М. Resistance to plastic deformation of metals and alloys. Reference book. Moscow : Metallurgiya, 1983. 352 p.

18. Shatalov R. L, Lukash А. S., Ziselman V. L. Definition of mechanical properties of copper and brass strips on indices of hardness factors in the time of cold rolling. Tsvetnye Metally. 2014. No. 5. pp. 61–65.
19. Tretyakov А. V. Zyuzin V. I. Mechanical properties of metals and alloys. Moscow : Metallurgiya, 1973. 221 p.
20. GOST 1497–84 (ISO 6892–84). Metals. Methods of tensile test. Introduced: 01.01.1986.
21. GOST 1173–2006. Copper foil, ribbons, sheets and plates. Specifications. Introduced: 01.01.2008.
22. GOST 1497–84. Metals. Methods of tensile test. Introduced: 01.01.1986.
23. GOST 2208–2007. Brass foil, ribbons, sheets and plates. Specifications. Introduced: 01.07.2008.