Journals →  Chernye Metally →  2021 →  #9 →  Back

Rolling
ArticleName Study of the friction coefficient during the steady-state process of continuous hot rolling of steel strips in conditions of the 1950 industrial mill
DOI 10.17580/chm.2021.09.05
ArticleAuthor A. E. Sevidov, A. V. Muntin, A. V. Rumyantsev
ArticleAuthorData

JSC Vyksa Metallurgical Works (Vyksa, Russia)1 ; Bauman Moscow State Technical University (Moscow, Russia)2:

A. E. Sevidov1,2, Leading Software Engineer, e-mail: sevidov_ae@vsw.ru
A. V. Muntin1,2, Cand. Eng., Deputy Director for Research

 

JSC Vyksa Metallurgical Works (Vyksa, Russia):
A. V. Rumyantsev1, Cand. Eng., Expert

Abstract

This paper describes a method for determining the value of the friction coefficient in a steady-state hot rolling under industrial conditions of the casting and rolling complex of “Vyksa Steel Works” located in Vyksa. The algorithm implies the forward slip method for determining the friction coefficient using the Ekelund formula. Measurements of hot rolling technological parameters from sensors are used as input parameters. Mathematical formulas are implemented in the ibaAnalyzer software, with the help of calculations are made for several thousand strips and data on the friction coefficient are obtained under various conditions. The data processing results demonstrate a normal distribution of the friction coefficient. The highest value of the friction coefficient is typical for the first finisher stands F1-F2, and the lowest values are found for the thinner gauge products rolled at high speed. The influence of the working layer of the work rolls on the friction value is demonstrated. High-chromium cast iron rolls have lower values of the friction coefficients, in contrast to indefinite cast iron, which is used for the working layer of the last finisher stands of mill 1950. A detailed comparison of the results with the classical methods for determining the friction coefficient in a steady-state process has been carried out. The dependence of the ratio of the friction coefficient during initial entry to the steady-state friction coefficient was refined.

keywords Friction coefficient, hot strip rolling, forward slip method, industrial conditions, steadystate rolling
References

1. Muntin A. V. Advanced technology of combined thin slab continuous casting and steel strip hot rolling. Metallurgist. 2019. Vol. 62. No. 9–10. pp. 900–910.
2. Muntin А. V., Kurenkov Yu. М., Kolesnikov А. G. Modern technological solutions and equipment for production of ultra-thin hot-rolled strip. Proizvodstvo prokata. 2016. No. 8. pp. 13–21.
3. Qin Z., Yu Y., Zhao W. et al. Development and application of ESP products in rizhao steel. Ibid. 2018. pp. 49–58.
4. Pigani A., Bobig p., Knights M. et al. Danieli Universal Endless (DUE) – the new evolution of Danieli thin slab casting and rolling plant. BHM Berg - und Hüttenmännische Monatshefte. 2016. pp. 429–439.
5. Kislitsa V. V., Lamukhin А. М. et. al. Casting and rolling complex are new technologies in production of pipe rolled products. Chernaya metallurgiya. Byulleten nauchno-tekhnicheskoy i ekonomicheskoy informatsii. 2013. No. 4. pp. 50–57.
6. Klein C., Cesere C., Meyer A. CSP and USP plants – the whole world of thin slab casting and rolling. Technologies from a single source. Metec-Estad. 2015. pp. 562–567.
7. Tselikov А. I., Tomlenov А. D., Zyuzin V. I. et. al. Rolling theory. Moscow: Metallurgiya, 1982. 335 p.
8. Grudnev А. p. Rolling theory. Moscow: Metallurgiya, 1988. 240 p.
9. Zaykov V. А., Polukhin V. p. et. al. Rolling process. Moscow: MISiS, 2004. 640 p.
10. Smolentsev А. А., Chikishev D. N. Contact friction in rolling production and determination of friction coefficient. Modelirovanie i razvitie protsessov OMD. 2019. No. 2. pp. 16–21.
11. Vasilev Ya. D. Investigation of the accuracy of determination of the physical friction coefficient during cold rolling by methods of forced braking of the strip and torque. Izvestiya vysshikh uchebnykh zavedeniy. Chernaya Metallurgiya. 2020. Vol. 63. No. 8. pp. 639–643.
12. Gorni A., Soares da Silvа M. Characterization of the friction conditions in the finishing stands of a hot strip mill. Tecnologia em metalurgia, materiais e mineração. 2012. Vol. 9. No. 2. pp. 103–108.
13. Yuen W. Y. D. Determinatiom of friction from measured forward slip and its applications in hot strip rolling. First Australasian congress on applied mechanics. 1996. pp. 927–932.
14. Panjkovic V. Friction and the hot rolling of steel. Taylor and Francis. 2014. 239 p.
15. Kriventsov А. М. Coefficient of friction at hot, cold and warm rolling of non-ferrous and ferrous metals. Design, calculation and research of rolling mills: Collection of scientific works. Мoscow: VNIIMETMASh. 1987. pp. 75–81.

Language of full-text russian
Full content Buy
Back