Belarusian State Technological University, Minsk, Belarus:

N. R. Prokopchuk, Professor of the Chair for Polymer Composite Materials, Associate Member of the National Academy of Sciense of Belatis, Doctor of Chemical Sciences, e-mail: nrprok@gmail.com
A. Yu. Klyuev, Professor, Chair for Woodworking Technology, Doctor of Technical Sciences, e-mail: tnsippm@belstu.by
I. O. Laptik, Engineer, Chair for Polymer Composite Materials, e-mail: inna.laptik@yandex.ru

St. Petersburg Mining University, St. Petersburg, Russia:

A. G. Syrkov, Professor, Chair for General and Technical Physics, Doctor of Technical Sciences, e-mail: syrkovandrey@mail.ru

Modification of the ZGV-101 model compound with nanodiamond particles, intended for precision casting of products from ferrous and nonferrous metals, produced by JSC Mining Wax Plant (Belarus), was carried out. Under laboratory conditions, a technology has been developed for introducing nanodiamond particles produced by the SP CJSC Sinta into the ZGV-101 model compound — the ASh-A brand diamond-containing charge and UDA SP brand ultrafine synthetic diamond. An assessment of the compatibility of nanoparticles with a model composition, depending on the method of its introduction has been carried out. Model compositions with different concentrations of nanoparticles were obtained, % (wt.): 0.005; 0.01; 0.05; 0.1. The heat resistance of ZGV-101 has been significantly improved; the dependences of softening temperature TS and Ubbelohde drop point TU on the concentration of nanoparticles were established, their nature was explained (a rapid increase in the heat resistance of model compounds at initial concentrations of 0.005% (wt.) and its subsequent decrease with a further increase in the content of nanoparticles). The reason for the increase in the heat resistance of the ZGV-101 model compound by nanodiamond particles at 0.001–0.005% (wt.) has been established. The hypothesis is related to the fact that at the given concentrations of nanoparticles, a spatial physical network is formed as a result of the interaction of the energetically active surface of nanoparticles with the carboxyl and hydroxide groups of components that make up ZGV-101. With an increase in the content of nanodiamond particles above 0.01–0.02% (wt.) in the composition, the uniformity of their distribution over the volume of the model compound is disturbed due to partial aggregation, and their connection with the functional groups of the composition components decreases.
The paper is recommended to be published by the Organizing Committce of the International Symposium “Nanophysics and nanomaterials (November 24–25, 2021, St.Perersburg, St.Perersburg mining university).

1. Petrov G. V., Shneerson Ya. M., Andreev Yu. V. Extraction of platinum metals during processing of chromium ores from dunnite deposits. Journal of Mining Institute. 2018. Vol. 231. pp. 281–286.
2. Syzyakov V. M., Brichkin V. N. About the role of hydrated calcium carboaluminates in improving the technology of compex processing of nephelines. Journal of Mining Institute. 2018. Vol. 231. pp. 292–298.
3. Shalygin L. M., Sizyakov V. M. Scientific school of metallurgists of the St. Petersburg Mining Institute (to the 300th anniversary of St. Petersburg and the 230^th anniversary of the first higher educational institution in St. Petersburg). Tsvetnye Metally. 2003. No. 7. pp. 4–13.
4. Aleksandrova T. N., Heide G., Afanasova A. V. Assessment of refractory gold-bearing ores based of interpretation of thermal analysis data. Journal of Mining Institute. 2019. Vol. 235. r. 30–37.
5. Jeevanandam J., Barhoum A., Yen S. Chan, Dufresne A., Danquah M. K. Review on nanoparticles and nanostructured materials: history, sources, toxicity and regulations. Beilstein Journal of Nanotechnology. 2018. No. 9. pp. 1050–1074.
6. Sivenkov A. V., Nikitina V. O., Serdiuk N. A., Konchus D. A., Pryakhin E. I. Creating a model of diffusion deposition of metal coatings from melts of low-melting metals. IOP Conference Series: Materials Science and Engineering. 2019. Vol. 560. p. 012188.

7. Mikhailov A. V., Serdiuk N. A. Sivenkov A. V., Pryakhin E. I. Surface alloying from the fusible metal melts. XII Russian-German Raw Material Forum: Youth Day. 2019. pp. 101–102.
8. Serdiuk N. A. Sivenkov A. V., Pryakhin E. I. The use of fluxes in technology of application protective coatings of low – melting melts. Science Reports on Resource Issues. 2019. Vol. 1. pp. 284–287.
9. Konchus D. A., Sivenkov A. V., Chirkova O. S. Influence of laser marking on the surface properties of 08Kh18N10 steel. Metalloobrabotka. 2018. No. 4. pp. 21–27.
10. Konchus D. A., Sivenkov A. V. A surface structure formation of stainless steel using a laser. Materials Science Forum. 2021. No. 1022. pp. 112–118.
11. Bolobov V. I., Kuvshinkin S. Yu. Materials science: steels with special properties, non-ferrous metals, non-metallic materials: textbook. Saint Petersburg : National Mineral Resources University “Gorny”, 2014. 94 p.
12. Radbil A. B., Kyuev A. Yu., Prokopchuk N. R. Development of scientific and applied foundations for deep and complex processing of resin of Scots pine Pinus Silvestris L. Khimicheskie tekhnologii, biotekhnologiya, geoekologiya. 2017. No. 1. pp. 41–53.
13. Kyuev A. Yu., Prokopchuk N. R. New directions of processing and use of pine resin. Minsk : BGTU, 2020. 232 p.
14. Grebler S., Prenner S., Kurz A., Resch S., Pavlicek A. et al. Polymer nanocomposites — additives, properties, applications, environmental aspects. Nanotrust dossier. 2020. No. 58. pp. 1–6.
15. Babaev A. A., Zobov M. E., Terukov E. I., Tkechev A. G. Technology for obtaining polymer composites based on carbon nanofibers. Fizikokhimiya poverkhnosti i zashchita materialov. 2020. Vol. 56, No. 4. pp. 416–421.
16. Stepa R. A., Kuhl K. Nanomaterials. Available at: http://oshwiki.eu/wiki/Nanomaterials (accessed: 28.05.2022).
17. Repyakh S. I. Requirements for model compounds of castings for especially critical purposes. Metall i lityo Ukrainy. 2010. No. 11. pp. 10–17.
18. Viala artigues renaud. Paste composition useful in reusable compositions obtained by mixing under heat a filler in powder form and wax. Pat. 2883881 FR. Accessed 14.02.2019. Published 06.10.2006.
19. Vorobyova M. I., Zhukova M. I. Compositions for the manufacture of investment casting models. Patent SU, No. 955611. Applied: 28.02.1981. Published: 20.03.2005.
20. Pat. 1579934 EP. Process for the production of a muffle for investment casing or model casting and composition of such a muffle. T. Wiest, S. Dierkes, M. Schlueter. Accessed 28.09.2005.
21. Poklad V. A., Ospennikova O. G., Pikulina L. V., Rassokhina L. I. Composition for casting investment patterns. Patent RF, No. 2447968. Applied: 14.12.2010. Published: 20.04.2012.
22. Rassokhina L. I., Parfenovich P. I., Narskaya A. R. Problems of creating model compositions of a new generation based on domestic materials for the manufacture of GTE blades. Novosti materialovedeniya. Nauka i tekhnika. 2015. No. 3. pp. 38–42.
23. Ospennikova O. G., Rassokhina L. I., Parfenovich P. I. Development of the composition of model compounds of a new generation with improved characteristics for the manufacture of blades and other parts of gas turbine engines. Novosti materialovedeniya. Nauka i tekhnika. 2016. No. 1. pp. 10–16.
24. Prokopchuk N. R., Globa A. I., Laptik I. O., Syrkov A. G. The properties of metal coatings enhanced with diamond nanoparticles. Tsvetnye Metally. 2021. No. 6. pp. 50–54. DOI: 10.17580/tsm.2021.06.07.
25. Technical Specification RB 100056180.003–2003. Diamond-bearing charge. Introduced: 05.02.2004. Minsk : NPZAO “Sinta„. 2004.
26. Technical Specification RB 28619110.001–95. Synthetic ultrafine diamonds. Introduced: 01.11.1995. Minsk: NPZAO “Sinta„. 1995.
27. GOST 23863–79. Wood chemical products. Methods for determination of the softening temperature. Introduced: 01.01.1981. Moscow : Izdatelstvo standartov, 1979.