Journals →  Chernye Metally →  2022 →  #6 →  Back

Rolling and other OMD processes
ArticleName Provision of allowance for the root and connecting rod necks and balancing of the forgings of the crankshaft of a heavy-duty vehicle
DOI 10.17580/chm.2022.06.07
ArticleAuthor D. T. Safarov, A. V. Chekh, A. G. Kondrashov
ArticleAuthorData

Naberezhnye Chelny Institute (branch) of Kazan Federal University, Naberezhnye Chelny, Russia:

D. T. Safarov, Cand. Eng., Associate Professor, Dept. of Materials, Technologies and Quality, e-mail.: Safarov-dt@mail.ru

A. G. Kondrashov, Cand. Eng., Associate Professor, Dept. of Design and Technological Support of Machine-Building Industries, e-mail: kondrashovag@mail.ru

 

PJSC KamAZ, Naberezhnye Chelny, Russia:
A. V. Chekh, Director of the Forging plant, e-mail: ChehAV@kamaz.ru

Abstract

The article discusses the requirements for balancing crankshafts. The unbalanced mass of the crankshaft after machining should be oriented in a certain angular sector, which ensures the removal of material in the opposite phase along the end surface of the counterweights. The existing calculation methods provide the specified imbalance conditions only at the design stage of the crankshaft forging by sorting through combinations of geometric accuracy indicators within the fields of their tolerances with simultaneous calculation of the position of the unbalanced mass. The method provides the design position of the unbalanced mass, but does not extend to the forging manufacturing process. The article considers the practice of machining production of changing the position of the machining base, which ensures the redistribution of masses. unprocessed elements of counterweights and the hit of an unbalanced mass in a given angular sector. Changing the position of the processing base completely redistributes the allowance for the root and connecting rod necks, which is not taken into account in the process of hot volumetric stamping of crankshaft forgings. The article presents a calculation scheme that allows taking into account changes in the position of the machining base, as well as mathematical dependencies that allow, according to measurements from the extreme trunnions of the crankshaft forging, to simulate the distribution of the allowance for the root and connecting rod necks from the machining base. Mathematical dependencies allow you to select the value of the adjustment displacements of the stamping equipment and ensure that there is an allowance for all angular phases of the main and connecting rod necks of the crankshaft forging.

keywords Forging of the crankshaft, hot stamping, allowance indicators, imbalance, machining base, adjustment displacements of stamping equipment
References

1. Dagna A., Delprete C., Gastaldi C. A general framework for crankshaft balancing and counterweight design. Applied Sciences. 2021. Vol. 11, Iss. 19. p. 8997. DOI: 10.3390/app11198997.
2. Manring N. D., Ali M. Modeling the inertial torque imbalance within an internal combustion engine: Quantifying the equivalent mass approximation. Journal of Dynamic Systems, Measurement and Control. Transactions of the ASME. 2018. Vol. 140, Iss. 7. pp. 1–35. DOI: 10.1115/1.4039282.
3. Zhou Q., Wang G., Shen L. Detection of cylinder imbalance in electronically-controlled diesel engine based on bandpass filtering. Qiche Gongcheng/Automotive Engineering. 2012. Vol. 34, Iss. 9. pp. 825–829.
4. Wang X., Mu L. A virtual crankshaft dynamic balance measuring system based on VB. 2012. Trans. Tech. Publications. Vol. 500. pp. 709–714. DOI: 10.4028/www.scientific.net/AMR.500.
5. Nazarov A. D. Reduction of wear of crankshaft bearings of V-8 engines by compensating the total unbalanced mass of the crank gear mechanism parts. Journal of Friction and Wear. Vol. 32, Iss. 5. pp. 345–355. DOI: 10.1115/1.4039282.
6. Ba J., Sun Z., Sandstrom A., Hu K., Li C., Shi Z. NVH analysis and optimization of engine balance shaft module. USA: SAE Technical Papers. 2021. 5 p. DOI: 10.4271/2021-01-1032.
7. Zhou C., Ding L., Lin L. On-line data analysis and optimization of crankshaft dynamic balance. Paper presented to the IOP Conference Series: Materials Science and Engineering. 2019. Vol. 646. Iss. 1. pp. 1–7. DOI: 10.1088/1757-899X/646/1/012035.
8. Volodin I. М., Chekh А. V., Volodin А. I. Study of the forging shape change during burr cutting. In the collection: Problems and prospects for the development of mechanical engineering. Collection of scientific papers of the international scientific and technical conference dedicated to the 60th anniversary of LSTU. Lipetsk. 2016. pp. 330–335.
9. Martyugin А. V., Volodin I. М. Reducing the effect of deformation during burr cutting on the geometric accuracy and imbalance of crankshaft forgings. Colloquium-journal. 2019. No. 26-2. pp. 91-94.
10. Martyugin А. V. Technological support for balancing heavy-duty vehicle crankshaft forgings. Izvestiya TulGU. Tekhnicheskie nauki. 2014. No. 11. pp. 176–183.
11. Volodin I. М. Simulation of hot die forging processes. Moscow: Mashinostroenie-1. 2006. pp. 199–215.
12. Martyugin А. V., Volodin I. М. Analysis of results of the study of crankshaft forging imbalance using a neural network. Colloquium-journal. 2019. No. 26. pp. 89–94.
13. Martyugin А. V., Volodin I. М., Volodin A. I., Biktimirova G. F. Improvement of the method for designing technological processes for hot die forging of crankshafts with unmachined counterweights. Izvestiya TulGU. Tekhnicheskie nauki. 2020. No. 5. pp. 1–8.
14. Martyugin А. V. Mathematical study of the geometric accuracy of forgings during stamping to ensure subsequent balancing of the crankshaft. Collection of scientific papers. In 9 parts. Novosibirsck: Nauka. Tekhnologii. Innovatsii. 2018. pp. 52–56.

Language of full-text russian
Full content Buy
Back