Journals →  Chernye Metally →  2022 →  #10 →  Back

Mechanical Engineering Technologies
ArticleName Investigation of damage and Hartfield fields in a steel semi-finished product at internal surface ribbing
DOI 10.17580/chm.2022.10.14
ArticleAuthor A. A. Pasynkov. S. S. Yakovlev, A. I. Gasanov
ArticleAuthorData

Tula State University, Tula, Russia:
A. A. Pasynkov, Cand. Eng., Associate Prof.
S. S. Yakovlev, Postgraduate Student, e-mail: yakovlev-ss-science@yandex.ru
A. I. Gasanov, Master’s Student

Abstract

The riffles formation on the inner surface of a cylindrical shell is studied by the method of local plastic forming. An analysis of the damageability of Gartfield fields in the process of ribbing to different depths using several types of the lead-in of working mandrels was carried out. These parameters were studied not only at the stage of applying the riffles, but also when removing the semifinished product from the working mandrel. The values of damage in the riffle cavity and the highest values of the Hartfield fields on the surface of the ribbed semi-finished product are given. The wear of the tool for applying the riffles was estimated. Computer simulation was carried out in the QForm program. Conclusions are drawn about which tool is better to apply riffles.
The study was supported by a grant from the Russian Science Foundation No. 22-29-20212, https://rscf.ru/project/22-29-20212/, and the Government of the Tula Region.

keywords Damage, cylindrical shell, tool, gap, local deformation, Kolmogorov method, Hartfield fields, ribbing, steel
References

1. Kukhar V. D., Yakovlev S. S. Innovative methods for applying a grid of riffles on the inner surface of the shells. Strategic development of the innovative potential of industries, complexes and organizations: Collection of articles of the IX International Scientific and Practical Conference, Penza, October 22–23, 2021. Penza: Penzenskiy gosudarstvenny agrarny universitet, 2021. pp. 57, 58.
2. Kukhar V. D., Yakovlev S. S. Die tooling for implementation of ribbing process. Izvestiya Tulskogo gosudarstvennogo universiteta. Tekhnicheskie nauki. 2022. No. 2. pp. 38–41.
3. Li Z., Lu S., Zhang T. et al. A Simple and low-cost lubrication method for improvement in the surface quality of incremental sheet metal forming. Transactions of the Indian Institute of Metals. 2018. Vol. 71, Iss. 7. pp. 1715–1719.
4. Kukhar V. D., Kireeva А. Е., Pasko А. N. Theoretical and experimental investigations of forging the «case» details via extruding of steel billets. Chernye Metally. 2018. No. 6. pp. 16–19.
5. Larin S. N., Platonov V. I., Nuzhdin G. А. Investigation of the quality parameter of the products obtained during isothermal free deformation of aluminum alloys into a square matrix. Izvestiya Tulskogo gosudarstvennogo universiteta. Tekhnicheskie nauki. 2018. No. 9. pp. 224–229.
6. Silva H. C., Lajarin S. F., Marcondes P. V. P. Analysis of numerically simulated true strain on high stampability sheets. Journal of the Brazilian Society of Mechanical Sciences and Engineering. 2010. Vol. 32, Iss. 1. pp. 21–27.
7. Kukhar V. D., Korotkov V. А., Yakovlev S. S., Shishkina А. А. Formation of a mesh of spiral wedge protrusions on the inner surface of a steel shell by local plastic deformation. Chernye Metally. 2021. No. 6. pp. 65–68.
8. Chan D. H., Nguyen M. T. Investigation of the influence of technological parameters of the first combined drawing on deformation damage. Izvestiya Tulskogo gosudarstvennogo universiteta. Tekhnicheskie nauki. 2017. No. 4. pp. 38–44.
9. Pasynkov А. А., Pasynkova N. S., Usenko N. А. Estimation of damage during isothermal reverse extrusion of pipe and bar billets from VT6S alloy. Izvestiya Tulskogo gosudarstvennogo universiteta. Tekhnicheskie nauki. 2020. No. 10. pp. 437–440.
10. Travin V. Yu., Tutyshkin N. D. Calculation of drawing operations with thinning of hull axisymmetric products with predictable structural parameters of the material. Izvestiya Tulskogo gosudarstvennogo universiteta. Tekhnicheskie nauki. 2021. No. 11. pp. 499–506.
11. Ovcharenko A. Yu., Tutyshkin N. D. Experimental analysis of deformation damage of structural metals. Izvestiya Tulskogo gosudarstvennogo universiteta. Tekhnicheskie nauki. 2018. No. 1. pp. 149–159.
12. Krivopalov I. V., Erisov Ya. А., Baturin А. P. Experience in mastering the technology of manufacturing large-sized forgings from 1570C alloy by hot volumetric deformation. Modern achievements in the field of creating promising light alloys and coatings for aviation and space technology: proceedings of the All-Russian Scientific and Technical Conference, Moscow, April 16, 2021. Moscow: Vserossiyskiy nauchno-issledovatelskiy institute aviatsionnykh materialov, 2021. pp. 33–43.
13. QForm 2D/3D – Program for modeling metal forming processes. "KvantorForm". Available at: https://qform3d.ru/files_ru/qform_manual_part1.russian.pdf (accessed: 01.01.2022).
14. Kolmogorov V. L. Stresses, deformation, fracture. Moscow: Metallurgiya, 1970. 229 p.

Language of full-text russian
Full content Buy
Back