Journals →  CIS Iron and Steel Review →  2022 →  #2 →  Back

IT Technologies
ArticleName Development of computational system based on artificial neural network for prediction of high temperature deformation behaviour in steels
DOI 10.17580/cisisr.2022.02.16
ArticleAuthor A. Yu. Churyumov
ArticleAuthorData

National University of Science and Technology “MISiS” (Moscow, Russia):

A. Yu. Churyumov, Cand. Eng., Associate Prof., Dept. of Physical Metallurgy of Non-ferrous Metals, e-mail: churyumov@misis.ru

Abstract

A significant number of the data about the hot deformation behaviour of the metallic materials is published up to date in the scientific sources. As a result, the systematization and formalization of such big datasets using mathematical modeling is required. However, the accuracy of the usual regression models is not enough for this purpose. The artificial neural network (ANN) based model for prediction of the steel flow stress under the hot deformation conditions was constructed. The model has shown a high accuracy on the training dataset such as on the independent additional compression tests of the stainless 13Cr11Ni2W2MoV steel. The compression tests were carried out in the strain rate range of 0.1, 1, and 10 s-1 and the temperature range of 1000 – 1200 ºC using thermomechanical simulator Gleeble 3800. The steel has a two-phase ferritic/austenitic microstructure in the hot deformation range. The average relative errors for the training dataset and approvement tests were about 8.8 and 9.5 %, respectively. The constructed model may be used for the determination of the different element influence the flow stress of the steel, which may allow fast correction of the hot deformation conditions. Special software was developed for the use of the built ANN-based model.

This research was funded by the Russian Science Foundation (project №18-79-10153-P)

keywords Artificial neural network, steel, hot deformation, microstructure, flow stress, thermodynamic calculations, thermomechanical simulator Gleeble
References

1. Gorbunova Y. D., Orlov G. A. Simulation of hot stamping of elliptical steel bottoms. Chernye Metally. 2019. No. 10. pp. 58–62.
2. Churyumov A. Y., Medvedeva S. V., Mamzurina O. I., Kazakova A. A., Churyumova T. A. United Approach to Modelling of the Hot Deformation behaviour, Fracture, and Microstructure Evolution of Austenitic Stainless AISI 316Ti Steel. Applied Sciences. 2021. Vol. 11. No. 3204.
3. Lisunets N. L. Improving the efficiency of the processes of billets manufacture from rolled metal via shift cutting based on simulation. Chernye Metally. 2018. No. 6. pp. 31–35.
4. Zhong L., Wang B., Hu C., Zhang J., Yao Y. Hot deformation behaviour and dynamic recrystallization of ultra high strength steel. Metals. 2021. Vol. 11. No. 1239.
5. Churyumov A. Y., Pozdnyakov A. V., Churyumova T. A., Cheverikin V. V. Hot plastic deformation of heat-resistant austenitic AISI 310S steel. Part 2. Tensile torsional fracture simulation. Chernye Metally. 2020. No. 9. pp. 32–38.
6. Zheng Y., Shen W., Zhu L., Guo Z., Wang Q., Feng J., Li Y., Cao R., Wu J. Effects of composition and strain rate on hot ductility of Cr-Mo-alloy steel in the two-phase region. High Temperature Materials and Processes. 2021. Vol. 40. pp. 228–240.
7. Churyumov A., Kazakova A., Churyumova T. Modelling of the Steel High-Temperature Deformation Behaviour Using Artificial Neural Network. Metals. 2022. Vol. 12. No. 447.
8. Zaitsev A., Arutyunyan N. Low-carbon Ti-Mo microalloyed hot rolled steels: Special features of the formation of the structural state and mechanical properties. Metals. 2021. Vol. 11. No. 1584.
9. Cai X., Hu X. Q., Zheng L. G., Li D. Z. Hot Deformation behaviour and Processing Maps of 0.3C–15Cr–1Mo–0.5N High Nitrogen Martensitic Stainless Steel. Acta Metallurgica Sinica (English Letters). 2020. Vol. 33. pp. 693–704.
10. Zhao C., Zhang J., Yang B., Li Y. F., Huang J. F., Lian Y. Hot Deformation Characteristics and Processing Map of 1Cr12Ni-2Mo2WVNb Martensitic Stainless Steel. Steel Research International. 2020. Vol. 93. No. 2000020.
11. Churyumov A. Y., Pozdnyakov A. V., Churyumova T. A., Cheverikin V. V. Hot plastic deformation of heat-resistant austenitic AISI 310S steel. Part 1. Simulation of flow stress and dynamic recrystallization. Chernye Metally. 2020. No. 8. pp. 48–55.
12. Lei B., Chen G., Liu K., Wang X., Jiang X., Pan J., Shi Q. Constitutive analysis on high-temperature flow behaviour of 3Cr-1Si-1Ni Ultra-high strength steel for modeling of flow stress. Metals. 2019. Vol. 9. No. 42.
13. Ghadar S., Momeni A., Tolaminejad B., Soltanalinezhad M. A comparative study on the hot deformation behaviour of 410 stainless and K100 tool steels. Materials Science and Engineering A. 2019. Vol. 760. pp. 394–406.
14. Ji G., Li L., Qin F., Zhu L., Li Q. Comparative study of phenomenological constitutive equations for an as-rolled M50NiL steel during hot deformation. Journal of Alloys and Compounds. 2017. Vol. 695. pp. 2389–2399.
15. Honysz R. Modeling the Chemical Composition of Ferritic Stainless Steels with the Use of Artificial Neural Networks. Metals. 2021. Vol. 11. No. 724.
16. Narayana P. L., Lee S. W., Park C. H., Yeom J.-T., Hong J.-K., Maurya A.K., Reddy N.S. Modeling high-temperature mechanical properties of austenitic stainless steels by neural networks. Computational Materials Science. 2020. Vol. 179. No. 109617.
17. Pourabdollah P., Serajzadeh S. A Study on Deformation behaviour of 304L Stainless Steel During and After Plate Rolling at Elevated Temperatures. Journal of Materials Engineering and Performance. 2017. Vol. 26. pp. 885–893.
18. Wan Z., Hu L., Sun Y., Wang T., Li Z. Hot deformation behaviour and processing workability of a Ni-based alloy. Journal of Alloys and Compounds. 2018. Vol. 769. pp. 367–375.
19. Churyumov A. Y., Khomutov M. G., Tsarkov A. A., Pozdnyakov A. V., Solonin A. N., Efimov V. M., Mukhanov E. L. Study of the structure and mechanical properties of corrosion-resistant steel with a high concentration of boron at elevated temperatures. Physics of Metals and Metallography. 2014. Vol. 115. pp. 809–813.
20. Mandal S., Sivaprasad P. V., Venugopal S., Murthy K. P. N. Artificial neural network modeling to evaluate and predict the deformation behaviour of stainless steel type AISI 304L during hot torsion. Applied Soft Computing Journal. 2009. Vol. 9. pp. 237–244.

Full content Development of computational system based on artificial neural network for prediction of high temperature deformation behaviour in steels
Back