Journals →  Chernye Metally →  2023 →  #6 →  Back

65 years of the Department of "Technology of Metals and Materials Science" Tver State Technical University
ArticleName Increasing the red hardness of the deposited layer of high-speed steel by thermomechanical effects
DOI 10.17580/chm.2023.06.05
ArticleAuthor A. M. Dozhdelev, A. Yu. Lavrentyev
ArticleAuthorData

Tver State Technical University, Tver, Russia:

A. M. Dozhdelev, Cand. Eng., Associate Prof., Dept. of Technology of Metals and Materials Science, e-mail: dozhdelev@gmail.com
A. Yu. Lavrentyev, Cand. Eng., Associate Prof., Dept. of Technology of Metals and Materials Science, e-mail: lavr_ay@mail.ru

Abstract

Currently, domestic enterprises are in dire need of high-quality Russian-made metal cutting tools. As a material for the working part of the cutting tool, you can use high-speed steel, which has a decent level of performance, allowing it to be successfully used in a variety of technological operations. It is advisable to manufacture such a tool by surfacing tool material, which makes it possible to reduce the consumption of expensive high-speed steel and at the same time form a working part of the required shape, which can be extremely important in the manufacture of shaped or stamping tools. The article considers the issue of increasing the red hardness of the deposited high-speed steel. The key factors influencing this property of the material are identified. As part of the study, samples of deposited high-speed steel R2M8 were analyzed. It is proposed to use surfacing with dual control of the process of electrode metal transfer in the arc, followed by surface plastic deformation (SPD) and high-temperature tempering. The use of double-controlled surfacing makes it possible to provide a high cooling rate of the deposited high-speed steel during hardening from the liquid phase in order to retain a larger amount of alloying elements in the solid solution, which contributes to an increase in the red hardness of the deposited high-speed steel. It was also found that accelerated cooling contributed to the formation of a high-speed steel structure with a large grain number. The subsequent SPD makes it possible to ensure the transformation of the residual austenite of the deposited high-speed steel into deformation martensite, to relax internal stresses caused by surfacing, and to reduce the subsequent heat treatment from three times to a single high-temperature tempering.

keywords Red hardness, heat resistance, high speed steel, hardfacing, tool, surface plastic deformation
References

1. Borodikhin М. А., Budkin М. А., Radishchev М. О. Features of heat treatment of high speed steel for cutting tools. World Science: Problems and Innovations. Proceedings of the XXXI International Scientific and Practical Conference: in 4 volumes. Penza: Nauka i Prosveshchenie, 2019. Vol. 1 (part 2). pp. 94–97.
2. Shunduo Wang, Yunbo Chen, Peng Pan, Zhenghua Lin, Lingli Zuo. Influence of Co on the microstructure and mechanical properties of M42 high-speed steel. Journal of Physics Conference Series. 2022. Vol. 2393. 012033.
3. Xiangyi Ren, Hanguang Fu, Jiandong Xing, Shuli Tang, Qi Zhang. Effect of calcium modification on solidification, heat treatment microstructure and toughness of high boron high speed steel. Materials Research Express. 2018. Vol. 6, Iss. 1. pp. 40–46.
4. Yu Liu, Dong Li, Qingli Shao, Haikun Ma, Jie Kang, Ru Su. Study on friction and wear behaviors of M42 high speed steel. Journal of Physics: Conference Series. 2021. Vol. 2168. pp. 41–50.
5. Shi Shaojun, Zeng Xianping, Sun Chengtong. Heat-treatment and properties of high-speed steel cutting tools. IOP Conference Series: Materials Science and Engineering. 2018. Vol. 423. pp. 50–56.
6. Barchukov D. А., Tsygvintsev А. V., Afanaseva L. Е. Features of the formation of the structure and properties of high-speed steel during pulse-arc surfacing. Vestnik Tverskogo gosudarstvennogo tekhnicheskogo universiteta. Seriya "Tekhnicheskie nauki". 2019. No. 4 (4). pp. 16–22.
7. Gvozdev А. V., Rasshchupkin V. P., Akimov V. V., Bayazitov R. B. Improvement of properties of high speed steel for cutting tools. Modernization and scientific research in the transport complex. Perm: Perm National Research Polytechnic University. 2012. Vol. 1. pp. 203–211.
8. Gureev D. М. Optimization of the heat resistance of high-speed steels with a combination of bulk and laser heat treatments. Vestnik Samarskogo gosudarstvennogo tekhnicheskogo universiteta. Seriya "Fiziko-matematicheskie nauki". 2014. No. 2 (35). pp. 156–167.
9. Martynov V. V., Taranova А. V., Evseev А. V. Evaluation of possibilities to improve the machinability of articles with a tool made of high-speed steel with a modified working part. Naukoemkie tekhnologii v mashinostroenii. 2020. No. 5 (107). pp. 19–22.
10. Cherenda N. N., Uglov V. V., Kashchevskiy А. М. et al. Modification of the phase composition and microhardness of the surface layer of high-speed steel under combined plasma and thermal effects. Zhurnal Belorusskogo gosudarstvennogo universiteta. Fizika. 2018. No. 2. pp. 61–70.
11. Zhigalov А. N., Goravskiy I. А. Experimental studies of wear of an axial milling tool made of R6M5 high-speed steel, hardened by an aerodynamic sonic method. Vestnik Baranovichskogo gosudarstvennogo universiteta. Seriya "Tekhnicheskie nauki". 2021. No.2 (10). pp. 24–41.
12. Chaus А. S., Maksimenko А. V., Fedosenko N. N. et al. Formation of the structure during laser melting of the surface of annealed high-speed steel. Fizika metallov i metallovedenie. 2019. Vol. 120. No. 4. pp. 400–407.
13. Butenko V. I., Zimbikevich D. V. Influence of laser processing of nickel-phosphorus coating on the tool life of metal-cutting tools. Molodoy issledovatel Dona. 2019. No. 1 (16). pp. 15–19.
14. Volodin V. L., Abalakin V. N., Gayduk V. V., Volodin Т. V., Rokkel V. R. Investigation of the influence of pulsed surface impacts on the structure and properties of R6M5 steel. Fundamentalnye problemy sovremennogo materialovedeniya. 2005. Vol. 2. No. 3. pp. 78–80.
15. Lavrentyev А. Yu., Dozhdelev А. М., Barchukov D. А. Changes in the structure and properties of the heat-affected zone in the manufacture of deposited tools from high-speed steels. Izvestiya Yugo-Zapadnogo gosudarstvennogo universiteta. 2014. No. 5 (56). pp. 14–20.
16. Dozhdelev А. М., Lavrentyev А. Yu. Method for manufacturing weld bimetallic cutting tool. Patent RF, No. 2627837. Applied: 24.02.2016. Published: 11.08.2017. Bulletin No. 23.
17. Barchukov D. А., Vavilov R. V., Yakimyuk R. I. Investigation of factors affecting crack formation in deposited high-speed steels. Vestnik Tverskogo gosudarstvennogo tekhnicheskogo universiteta. Seriya "Tekhnicheskie nauki". 2020. No. 2 (6). pp. 21–27.
18. GOST 9450–76. Measurements microhardness by diamond instruments indentation. Introduced: 01.01.1977.
19. GOST 19265–73. Bars and strips of high-speed steel. Specifications. Introduced: 01.01.1975.
20. GOST 5639–82. Steels and alloys. Methods for detection and determination of grain size. Introduced: 01.01.1983.

Language of full-text russian
Full content Buy
Back