Journals →  Tsvetnye Metally →  2024 →  #6 →  Back

COMPOSITES AND MULTIPURPOSE COATINGS
ArticleName Influence of hardening on mechanical properties of hard alloy VK8
DOI 10.17580/tsm.2024.06.06
ArticleAuthor Kozik E. S., Svidenko E. V.
ArticleAuthorData

Orenburg State University, Orenburg, Russia
E. S. Kozik, Associate Professor, Candidate of Technical Sciences, e-mail: ele57670823@yandex.ru
E. V. Svidenko, Associate Professor, Candidate of Technical Sciences, email: tzvetkova.katia2016@yandex.ru

Abstract

In mechanical engineering, a special role belongs to the quality of tools that determine the productivity of machines in many respects and the machining cost in general. The quality of tools can be improved by various types of machining. The development and improvement of technological processes in many industrial sectors are inextricably linked with the use of hard alloys. Sintered hard alloys are of great importance in modern equipment. Such materials are widely used as cutting, wear-resistant, drilling, stamping tools; they gain increasing use in equipment operating at high temperatures and in aggressive environments. Now, there are many methods of testing carried out on hard alloys. This article presents the results of mechanical tests on hard alloy VK8. We determined mechanical properties and strain of a part. The article describes the influence of various types of heat treatment, namely high frequency heating, and heating in the electrolyte in salt bath furnaces, on mechanical and performance properties of hard alloy VK8. Heat treatment was conducted in the salt bath furnace with a composition of 28% NaCl + 72% BaCl2; Theating = 795–1235 оC. To carry out heating for quenching, we used the high frequency heater, LH-30KW-B, for annealing — the laboratory vacuum furnace, SUOL 0.4.4/1200, filled with graphite. The hard alloy VK8 ingots were tested for bending failure on tensile testing machine model IR5047-50-10 after different heat treatment modes. Microhardness was measured according to the Vickers method on the PMT-3 microhardness tester. Diamond abrasive wear was determined on a special friction tester. To study microstructures of the samples, we used μVizo-МЕТ-221, an optical microscope, and JEOL JCM-6000 Neo Scope II, an electron microscope. Mini-diffractometer MD-10 was used to get X-ray diffraction patterns of the materials under study to conduct their X-ray structure analysis.

keywords Strain measurement, ingots, hard alloys, bending test, microstructure of hard alloys, wear resistance, cutting wear.
References

1. Kreymer G. S. Strength of hard alloys. Moscow : Metallurgiya, 1971. 247 p.
2. Panov V. S., Chuvilin A. M. Technology and properties of sintered hard alloys and products from them. Moscow : MISIS, 2001. 428 p.
3. Suzuki H., Hayashi K. Strength of WC – Co cemented carbides in relation to their fracture sources. Planseeber. Pulverment. 1975. Vol. 23, No. 1. pp. 24–36.
4. Guo Zhixing, Xiong Ji, Yang Mei, Jiang Cijin. WC – TiC – Ni cemented carbide with enhanced properties. J. Alloys and Compnd. 2020. Vol. 465, No. 1–2. pp. 157–162.
5. Tokova L. V., Zaitsev A. A., Kurbatkina V. V., Levashov E. A. et al. Features of the influence of ZrO2 and WC nanodispersed additives on the properties of metal matrix composite. Russian Journal of Non-Ferrous Metals. 2019. Vol. 55, No. 2. pp. 186–190.
6. Bock H., Hoffman H., Blumenauer H. Mechanische Eigenschaften von Wolframkarbid-Kobalt-Legierungen. Technik. 1976. Vol. 31, No. 1. pp. 47–51.
7. Bogodukhov S. I. Materials Science. Moscow : Stary Oskol, 2021. 536 p.
8. Colovcan V. T. Some analytical consequences of experiment data on properties of WC – Co hard metals. Int J. Refract. Met. Hard Mater. 2021. Vol. 26, No. 4. pp. 301–305.
9. Zhang Li, Wang Yuan-Jie, Yu Xian-Wang, Chen Shu et al. Crack propagation characteristic and toughness of functionally graded WC – Co cemented carbide. Int. J. Refract. Met. Hard Mater. 2020. Vol. 26, No. 4. pp. 295–300.
10. Gurland J. The fracture strength of sintered WC – Co alloys in relation to composition and particle spacing. Trans. Met. Soc. AIME. 1963. Vol. 227, No. 1. pp. 28–43.
11. Bondarenko V. A. Ensuring the quality and improving characteristics of cutting tools. Moscow : Mashinostroenie, 2000. 428 p.
12. Bogodukhov S. I., Kozik E. S., Svidenko E. V. Influence of heating hard alloys of VK and TK groups in various media on the surface quality. Izvestiya vuzov. Tsvetnaya metallurgiya. 2022. Vol. 28, No. 6. pp. 71–80.
13. Bogodukhov S. I., Garipov V. S., Svidenko E. V. Determining an elastic modulus of various materials with strain metering units. Vestnik Orenburgskogo gosudarstvennogo universiteta. 2014. No. 4. pp. 289–295.
14. A. G. Sokolov. Method of hard-alloy tool machining. Patent RF, No. 2509173. Published: 10.03.2014.
15. Kim C. S., Massa T. P., Rohrer G. S. Modeling the relationship between microstructural features and the strength of WC – Co composites. Int. Journal of Refractory Metals and Hard Materials. 2020. Vol. 24, No. 1. pp. 89–100.
16. Yamamoto T., Ikuhara Y., Watanabe T. et al. High resolution microscopy study in Cr3C2-doped WC – Co. Journal of Materials Science. 2021. No. 36. pp. 3885–3890.
17. Bogodukhov S. I., Kozik E. S., Svidenko E. S. Hard alloys hardening method. Patent RF, No. 2693238. Published: 01.07.2019.
18. E. Khindrik. Cutting tool insert for steels turning. Patent RF, No. 2536014. Published: 20.12.2014.
19. Slesarchuk V. A. Materials science and technology of materials. Minsk : RIPO, 2019. 391 p.
20. Jaensson B. O. Die Untersuchung von Verformungsersheinungen in hochfeste WC – Co-Legierungen mit Hilfe eines neuen Localisierungsverfahrens fur die Abdruck elektronenmicroscopie. Pract. Metallogr. 1972. Vol. 9, No. 11. pp. 624–641.
21. GOST 19064–80. Pentagon throw-away (indexable) carbide cutting inserts with cylindrical holes. Design and dimensions. Introduced: 01.01.1982.
22. GOST 9450–76. Measurements microhardness by diamond instruments indentation. Introduced: 01.01.1977.
23. GOST 9206–70. Diamond powders. Specifications. Introduced: 01.07.1981.

Language of full-text russian
Full content Buy
Back