Journals →  Eurasian Mining →  2024 →  #1 →  Back

EQUIPMENT AND MATERIALS
ArticleName Tracking prevention in roller cone bit drilling
DOI 10.17580/em.2024.01.15
ArticleAuthor Toshov Zh. B., Rahutin M. G., Toshov B. R., Baratov B. N.
ArticleAuthorData

Tashkent State Technical University named after Islam Karimov, Tashkent, Uzbekistan

Toshov Zh. B., Dean, Professor, Doctor of Engineering Sciences

 

NUST MISIS, Moscow, Russia

Rahutin M. G., Professor, Doctor of Engineering Sciences, rahutin.mg@misis.ru

 

Navoi State Mining and Technology University, Navoi, Uzbekistan

Toshov B. R., Associate Professor

 

NUST MISIS’ Division in Almalyk, Almalyk, Uzbekistan

Baratov B. N., Dean, Candidate of Engineering Sciences

Abstract

In the world practice of open pit mining, drilling is mainly carried out using roller cone bits. The cost of drilling totals 25–40% of the overall cost of mining. One of the factors which worsen drilling efficiency is tracking which occurs when spiked teeth of the cones fall into the same craters cut during previous rotations of the bits, and which increases wear of the drilling tool and decreases the rate of drilling. This article proposes a calculation algorithm for the contact paths of teeth in the peripheral rows of roller cones using actual involutes of toroidal surfaces in the periphery of the well bottom. The algorithm provides a sufficiently accurate mesh of coverage of the well bottom periphery by tricone drill bits with the offset spin axes of roller cones with a view to preventing tracking. The proposed algorithm can be used for the design and reasonable selection of the roller cone bits with regard to geological conditions of drilling.

keywords Roller cone bit, tracking, peripheral teeth row, path, contact points, coverage mesh, tooth
References

1. Baratov B. N., Umarov F. Ya., Toshov Zh. B. Tricone drill bit performance evaluation. Gorniy Zhurnal. 2021. No. 12. pp. 60–63.
2. Inoue T., Rheem C.-K., Kyo M., Sakaguchi H., Matsuo M. Y. Experimental study on the characteristics of VIV and whirl motion of rotating drill pipe. ASME 2013 32nd International Conference on Ocean, Offshore and Arctic Engineering. 2013. Vol. 7. pp. 9–14.
3. Blinkov O. G. Ways to enhance efficiency of roller cone rock bits : Theses of Dissertation of Doctor of Engineering Sciences. Moscow, 2007. 359 p.
4. Menezes P. L., Lovell M. R., Higgs C. F. III. Influence of friction and rake angle on the formation of discontinuous rock fragments during rock cutting. STLE/ASME 2010 International Joint Tribology Conference. 2010. pp. 271–273.
5. Blinkov O. G. Determination of effective geometric parameters of carbide drilling roller bits depending on the mechanical properties of the rocks. Equipment and Technologies for Oil and Gas Complex. 2022. No. 1(127). pp. 27–31.
6. Toshov Zh. B., Baratov B. N., Toshniyozov L. G., Ochilov S. T. Technology of drilling tool engineering. Gorniy vestnik Uzbekistana. 2018. No. 1. pp. 71–74.
7. Naganawa S. Dynamics modeling of roller cone bit axial vibration. Journal of the Japanese Association for Petroleum Technology. 2005. Vol. 70, Iss. 4. pp. 333–337.
8. Shilin Chen. Roller-cone bits, systems, drilling methods, and design methods with optimization of tooth orientation. Patent US, No. 6,412,577 B1. Published: 02.07.2002.
9. A. V. Aaron, V. Litvienko. Antitracking earth boring bit with selected varied pitch for overbreak optimization and vibration reduction. Patent US, No. 7,195,086 B2. Published: 27.03.2007.
10. Blinkov O. G. Study of tracking (rack formation) at the wellbottom. Construction of Oil and Gas Wells on Land And Sea. 2021. No. 12(348). pp. 24–28.
11. Das M. K., Sarkar S., Choudhary B. S. Experimental and numerical analysis of rotary tricone drill bit and its wear prediction. Journal of the Brazilian Society of Mechanical Sciences and Engineering. 2018. Vol. 40, No. 366. DOI: 10.1007/s40430-018-1292-4
12. Tian J., Zhang T., Dai L., Cheng W., Yang L. et al. Dynamic characteristics and test analysis of a new drilling downhole tool with anti-stick–slip features. Journal of Mechanical Science and Technology. 2018. Vol. 32. pp. 4941–4949.
13. Toshov J. B., Toshov B. R., Baratov B. N., Haqberdiyev A. L. Designing new generation drill bits with optimal axial eccentricity. MIAB. 2022. No. 9. pp. 133–142.
14. Toshniyozov L., Mamatov M. Analysis of drill bit speed in bit–rock interaction with the use of numerical simulation methods. Ukrainian School of Mining Engineering — 2020. E3S Web of Conferences. 2020. Vol. 201. ID 01006.
15. Bulatov A. I. Drilling engineer’s handbook : In 4 books. Moscow : Nedra, 1995. 272 p.
16. Benavides-Serrano A. F., Peña-Sabogal A. S., León O. M., Sánchez-Acevedo H. G., González-Estrada O. A. Optimization of parameters in material selection of tricone drill bit head design. Journal of Physics: Conference Series. 2019. Vol. 1159. ID 012018.
17. Kryukov G. M. Physics of rock fracture in drilling and blasting. Moscow : Gornaya kniga, 2006. Vol. 1. 330 p.
18. Kricak L., Negovanovic M., Mitrovic S., Miljanovic I., Nuric S. et al. Development of a fuzzy model for predicting the penetration rate of tricone rotary blasthole drilling in open pit mines. The Journal of the Southern Africa Institute of Mining and Metallurgy. 2015. Vol. 115, No. 11 pp. 1065–1071.
19. Rahimov R. M. Method to assess working efficiency of one-cone drill bits : Theses of Dissertation of Candidate of Engineering Sciences. Tashkent, 2002. 107 p.
20. Ibragimova P. I. Analysis of functions in energy input pattern in dynamic systems at extremum. Construction of Oil and Gas Wells on Land and Sea. 2005. No. 11. pp. 19–25.

Full content Tracking prevention in roller cone bit drilling
Back